Does anyone know the pinout for a 1998 US spec Land Cruiser 100? After the battery died none of my keys are recognized by the immobilizer. I swapped ECU with my 2000 Lexus LX 470 and it will start right up(with Lexus key beside ignition cylinder). All the videos on the internet say to jumper...
Ok I did an exhaustive search (maybe I missed I hope I did) and my Dad's 100 became a 105 this summer by doing a SAS. he had axles made by Diamond axles and had the 80 abs sensors fitted due to the 80 knuckles used. so our fabricator wired them up and was not able to get the abs code on the OBD2...
Hi all,
I am new to this forum but have loved what I have read thus far. Just a quick intro, I am based in Melbourne, Australia and have just purchased a 2019 Landcruiser Sahara (200 series.
It’s my first cruiser so am super excited.
Now my question if I may? I want to purchase an OBD2...
Hi all,
1999 LC, 105 series, 1HZ (HZJ105R)
Still experiencing a crank-no-start issue with the ol' LC, next idea that came to mind was to located the OBDII port just to see if there were any codes that could give me some pointers as to what exactly is going wrong. Interestingly, I watched this...
I'll get right to the point. I have a 1994 TLC. It's got 300k miles and burns ALOT of oil. The plan is to completely rebuild the motor over the winter season. There is multiple reasons I want to do a complete rebuild other than just the oil burning. A big reason for the rebuild is so I can gain...
1996 FZJ80 LandCruiser
280,000 miles
$10,500 OBO/ No trades
No LOCKERS
Clean Title
Fort Collins, CO
Looking to sell my 96 landbruiser to fund fixing up my 60 series... She’s no show queen but a well maintained/ recently baselined rig with 280,000 miles. No rust on the body or frame. Interior is...
Hey guys, so I just got my first land cruiser 2 months ago. I was trying to program a key and i couldn't, then I put a dungle to use it with torque and didn't work either, finally i got a handheld code reader and when i plugged it in, it didnt have any power. I checked for bended pins but they...
Graduation test shows only 8 bars, the fluid has 20k miles on it, rear springs are OEM from 1999 and torsion bars have never been cranked. The ride has been getting significantly harsher in the last 15k miles and I have No leaks anywhere on the system (struts, accumulators and globes, pump)...
I am trying to figure out how to change the transmission in my 97 FZJ80 and get more gears. One of the biggest hurdles is keeping the CEL off, (I live in an emissions tested area).
Over the years on Mud, every time I read about someone thinking of a manual swap, it was shot down because of ecm...
Though I have owned an 80 for close to 20 years, thankfully my 80 has been dependable so I haven’t done any diagnostics on it. The few CELs that came up over the years handled by shops like Iron Pig.
My troubleshooting skills, meager as the are, were rooted in the carburetor age.
Both of my...
I need a replacement engine for my blown up 96 cruiser i just picked up. Id be willing to drive a bit to get it. Let me know what you have and hopefully we can work something out.
"I breakdown in the middle and lose my thread"; sorry I was having an Alan Parsons flashback.
Recently, someone posted a thread referencing their OBDII-Samsung tablet solution. The photo in the post shows the tablet lying on the instrument cluster, above the steering column. I've looked and...
Hey guys, this is my thing:
I have a 2007 FZJ80 (From Venezuela) and it doesn't have the OBD-II connector
Can it be added? From what I understand, it has 4 contacts (2, 4, 5 and 16)
Would it be as easy as adding those 4 connectors? Where is that wiring going?
What do you think?
Thanks in...
I have Engine light + VCS + VSC lights on during an offroad trip.
A guy plugged in his OBD2 and said it is the catalytic converter.
The oxygen sensor there was rattling, the screw was missing the nut I guess, so we tightened it with wire.
My question:
now I wanna get my own OBD2 so I can get...
On my 96, I have a CEL and want to see if there are any codes. So I plugged in the OBD2 and started Torque on my phone. It just keeps trying to connect and no matter what it says it cannot communicate with the ECU (or ECM - forgot which terminology it uses).
I actually tried 3 different OBD2...
I've been the proud owner of a high-mileage 1999 LC for just over a week, and the check engine light started flashing at me today. I'm just starting to learn the ins and outs of maintaining a LC, so I dropped it off at a local mechanic and will find out tomorrow what the problem is. Based on...
I am preparing to install a TRD SuperCharger on my 2000 LC. Bought a OBD2 scanner and I am using Torque Pro to monitor/log data. Any advise on what/how to monitor specifically to identify any existing issues with the engine/fuel system that might be aggravated by a SC? I have been monitoring...
I made an account just for this.
My engine has had the P0401 code for awhile. not really a big deal, it has run fine. Recently it has kicked back the P0335 (crankshaft position sensor), P0340 (camshaft position sensor), and P0385 (crankshaft position sensor another one?). I don't know what to...