engine

Just bought a '97 80. Heat blows cold. Front heater core flushed and clear. Coolant level OK. Temp valve opening. I noticed that there is zero pressure on the inlet hose( driver's side) when engine is running. Then I noticed that when I pressurized the radiator with a garden hose water blasted...

hey guys i’m 24 years old got this baby when I was 16 and had 30k miles on it. 1996 dark green fj80 that was immaculate. it’s been my everything for years and i’ve always taken care of it finally got an entire new exhaust have never had any major problems. kept flushing the ac system to get the...

We've had this Landcruiser for about 20 years. Modified it with 4 wheel discs (Poser mod), H42 4 speed with 3 speed transfer case, rebuilt F.5 engine, DUI distributor, Howell fuel injection, Paki soft top (top needs replacement), 33x9.5x15 BFG's on Toyota steelies, Nason's Dune Beige 416 paint...

after some tedious back and forth with mechanics, i had come to conclusion that my injectors needed replacing. during the weekend i had purchased new injectors and decided to replace them, after replacing them putting everything back as it was, replaced some old vacuum lines and tightened...

I've been lurking on here and I decided to join up. I have a 1984 that the PO tore apart and 99% kept in boxes or bags. They block, crank, and head are at a local machine shop getting verified for a rebuild or if they are boat anchors. I did find a burnt valve with the top end stuff. Four valve...

Hi All, I have a 2003 LX470 that - like many of us - I've personalized quite a bit. Brand new 33" tires, brakes, rotors, bearings, custom bamboo tailgate cover / drawer system, lithium ion battery system, front and rear lockers, 4.30 gearing (5spd normally 4.11), completely rebuilt front and...

Looking for an engine crank handle for a 25 or early 40 series, like in the photo below posted by @IDave a long time ago. Not sure which length came in which years, but not going to be picky - either one would be awesome. I understand some Madza trucks had similar cranks, but the length...

Looking for a fan shroud for my 78 FJ40. I have the fan clutch if that matters. Thanks!

Hello All, I have a 2F engine and 4 speed transmission from a 1985 FJ60 for sale. I will sell them separately or together. These came out of a truck with 180k miles on it. The transmission shifts nicely and is in nice shape. The engine runs well with good compression but burns a lot of oil...

Never used it. paid $395. This is yours for $375 shipped.

I've got a full powertrain out of a 1972. F Motor, 3 speed, and transfer case ($600). Motor will need a rebuild. Also have another freshly milled F block ($200) and a Weber carb ($200) for sale. Can ship the Carb. Pickup only for the powertrain. Thanks

My 2f cylinder head is cracked, casting 61040. I am looking for one that is good to go. I don't care if it's ready to install, I just need one that's not cracked.

Getting my 1996 Prado soon 1KZ-TE engine, I am from Alberta, wondering what kind of oil you guys all using? do you switch oil type between summer and winter?

I am on St Simons Island w/ a '79 FJ that I have owned for 12 years. Engine just turned 100K, but due to oil leakage, I may need to look into engine work. Any references for shops in GA, SE SC or northern FL? Thanks in advance.

After every project, I have a stack of things that I’m sure I’ll use sometime in the future. Well, the future is in the rearview mirror and they’re still collecting dust. Kind of a pot porie of some various mounting brackets, coolant pipes and fuel lines along with assorted gaskets as well as...

Had a weird issue happen the other day and not seeing a similar issue with my searches so i am reaching out to get some thoughts. This past week I hopped in the truck after driving to the gym early last week. No noticed issues driving there. Temps were mild, in the mid 40's (AZ) Put the...

Hey y’all, I’m planning on rebuilding the engine out of my 1994 80 Series. Is there anyone local to the HHI/Beaufort area with an unused engine crane and engine stand that they’d be willing to rent for a couple months? Preferably a 2-ton picker, as I am planning to pull the 1FZ-FE, A442, and...

3UZ 5 Speed Engine, with Ecu flashed & bypassed and wiring all done FOR automatic application - $2500 1 x 3UZ 5 SPEED ENGINE 1 x ECU - Immobilizer has been bypassed and flashed. 1 x OEM Wiring harness system which is all wired up for automatic application - Just 3 wires to connect to make it...

Hi guys. I just replaced my steering rack today. I took off my whole radiator assembly. But after everything put back. My water temp went to the top. I quickly shut off the car and put more water in the radiator. Everything seems works fine. However I was waiting a train to pass. The temp slowly...

I have a 1fz-fe which i got for my 97, that I dropped a little over a grand of parts at. When i put it in, i had no idea that it had needed a head gasket...until I ran it. It came out of a 95 that had 220k on it. The water pump, oil cooler internals, thermostat, power steering pump, valve cover...