engine

I am needing the engine wiring harness for a 1991 landcruiser from the ECM to the injectors and all the other sensors looking for as complete as possible. Let me know what you want shipped to utah 84010. PM or email me at stielow775@hotmail.com Thanks so much Matt

So, my engine mounts are shot. My car is a G spec 200 with a 1VD and manual box. Bare bones, UN spec, but it seems this bring some challenges. The engine mounts on my car are oil filled but have no vacuum tubing. These mounts are only specifically fitted to my spec of vehicle, which is rare...

I have a 4 speed trans from a 1984. Bought the trans/transfer combo but don't need the trans. Turns by hand and I can get additional photos of the inside. $350 plus shipping cost. (Runs around $200) Thanks.

15

New to the forum. New to the Brits, so ignorant on them. I'm helping my son with a 1993 110 build. He is thinking going with the BMW n54 & the 8HP45 trans. Me personally, no fan of BMW due to $$$. Reading on here with some of the n45 engines, sounds like issues. I'd rather do a 6.0 LS engine due...

$80 Shipped CONUS

Hi Everyone, I'm hoping there is some sort of checklist that's out there to what should be checked to ensure nothing is missed. So as the title says, the engine turns but doesn't start up. No check engine lights are on. The one odd thing is that the stereo no longer turns on (stock stereo)...

Om606 turbo i picked up with 140k miles in a merc. Its also on an engine stand - already has a brand new DieselPumpUK I.P. imported installed with the 300hp pumps. I think that pump was around $1200ish to import. Motor and pump with a few other items like the Advanced adapter bell...

I picked this up as a backup from a buddy. Ran when pulled but i never got around to using / needing it. You can also have the engine stand and i have a lfit to pick up the whole enchilada for you. its in a carport so even a rainy day wont be much hasselhoff. Just paying it forward if anyone...

hi , any help with clues or verified TECH on this unique 2-sensor sub harness section ? Is the smaller thin tall rubber boot for a knock sensor or a idiot light secondary oil switch the 79-89 20R / 22R / 22RE folks might know and narrow down this Sub Harness section in the engine bay...

I am currently taking apart my 1FZ and I noticed that the stamping on the block does not match with the vin on the body. Are they supposed to match or is it just an American car thing?

I was driving around for a while with low compression on one of the cylinders, had no idea that the other one was bad too. Car has 199K on it Many thanks for any insight into how this happened and how to prevent in future.

Looking for a good running 3FE engine with good compression all around for an 88-90 model FJ62. Prefer near Nashville or TN, if possible but open minded about shipping for the right engine! Thanks!

Doing the TorFab engine swap on my 91 80 Series and need the adapter from the A343 transmission and the 6 bolts that hold it to the transfer case (PN: 35015-60070). Shipped to 76103.

Bought this near new from Toyota h55f from an employee at Mudraks who used it for 8k miles and then popped a cummins/nv4500 in his 60. Pulled this one out. George of Valley Hybrids rebuilt another split case i had and upgraded the case with all the bells n whistles/McNamera gear etc. and...

I bought an 80 with a bad head- and the owners records showed Toyota replacing the bottom end with a new $6000 block at a Toyota dealer.:oops: I pulled the motor/trans and kept it as a spare and now i dont need it. I pulled the head to use for another project and also just to see what an...

$500 shipped to CONUS

I installed OEM freeze plugs (96411-45000) in my f engine and they don’t set in all the way. This doesn’t look right, but they won’t go in any further. I did put a light coating of permatex pipe dope on the hole lips, but that shouldn’t be the problem if there is one. Any ideas? Thank you! Mike

1991 FJ80 restoration project -- when the ambient temperature is above the high 20s or low 30s, or if I let the vehicle warm up thoroughly, the brakes work great. Below the mid 20s and if the engine is cold, the brakes do not work at all. Hard pedal at the right height, just no stopping power...

97 TLC. Essentially unmodified from stock, but massively reconstructed...frame swap etc, so if there is something wrong, its likely my doing. Yes, it ran before the teardown. So I've got the beast all back together from frame swap and professional head rebuild. Engine starts and idles...