engine

Hey y’all, I’m planning on rebuilding the engine out of my 1994 80 Series. Is there anyone local to the HHI/Beaufort area with an unused engine crane and engine stand that they’d be willing to rent for a couple months? Preferably a 2-ton picker, as I am planning to pull the 1FZ-FE, A442, and...

3UZ 5 Speed Engine, with Ecu flashed & bypassed and wiring all done FOR automatic application - $2500 1 x 3UZ 5 SPEED ENGINE 1 x ECU - Immobilizer has been bypassed and flashed. 1 x OEM Wiring harness system which is all wired up for automatic application - Just 3 wires to connect to make it...

Hi guys. I just replaced my steering rack today. I took off my whole radiator assembly. But after everything put back. My water temp went to the top. I quickly shut off the car and put more water in the radiator. Everything seems works fine. However I was waiting a train to pass. The temp slowly...

I have a 1fz-fe which i got for my 97, that I dropped a little over a grand of parts at. When i put it in, i had no idea that it had needed a head gasket...until I ran it. It came out of a 95 that had 220k on it. The water pump, oil cooler internals, thermostat, power steering pump, valve cover...

1991 LJ78 2L-TE, Automatic Transmission I'm embarrassed to admit it, but I unknowingly ran my engine low on oil - not sure how long. Could have been low for a couple weeks. I changed the oil about a month ago (filled to proper level at that time) and have done mostly city driving since then...

Have 2 with 130k ish miles on them. Include all accessories. Can do for $10.5k. I have them listed in the products section on my website now! www.legendarytoyota4x4s.com

Hey I’m just wondering what is an acceptable amount of air to be blowing out of the oil filler hole. This is a 3b diesel. Mine seems to have a fair bit, but it’s done it since I bought it 6 years ago. I want to say it feels like a hair dryer but it’s not nearly that high, maybe like a heat gun...

Was lucky enough to find a healthy running 3b motor and now I have mission of pulling my old one out. My question is, is there any bits and pieces (that arnt entirely obvious) that I'll need for the swap.

Hi I have this 1HD-FTE which needs to find a new home. It came from an EU spec 4 speed auto Hdj-100 with 430.000 km on the clock. Comes as: - engine complete with all accessories, except the airco compressor and alternator - engine wiring loom - Automatic ECU, spill valve control, immobilizer...

Everything is best offer. I’ve got an engine and transmission for sale. Approximately 250,000 on both. Engine runs good, fan belt squeaks due to a 1/2” belt thats worn out from night being tight enough. Runs good, has maf hei distributor, Webber 38/38 carb, billet pushrod cover. Runs like a top...

New Never installed part time spool for 90-07 80/100 transfercases. Was originally purchased from CruiserTeq. $500 shipped to lower 48. Pm if interested.

Has anyone installed a 5.7 gas Toyota V8 engine in an 80-Series?

The Lexus was so quiet at idle for years that I sometimes didn't know it was running and tried to start it again. My 2006 has 160k miles and while not terrible I can feel it idling. Is this due to motor mounts aging? What causes this, what can be done to remedy, and how much would it cost?

I have check engine light with loss of power and rough engine. Check engine light with code misfire on cylinder 3. This only happens when driving on interstate 65-70 mph. The truck will recover and run normal below 60 mph. I plan to replace plug and wire. Any other suggestions? Thanks

I have a 97 LC with an engine that may need swapped out. If I were to source a JDM spec motor from landcruiser heaven would it be a simple “one for one” swap or would I run into wiring harness and electrical readout issues since the JDM spec motor does not have an ERG ?

Hey all. I bought this crate with a complete 1f engine (F222837)(1967?). It spun a bearing and the owner went with a sbc. Picked crank up at machine shop, was told it needs .040" bearings. Looks to all be here. I have no use for it, but couldn't let it go. Do I part this thing out or sell as a...

Have a nice clean transfer case came from a 96 80 series with 166K on the odometer. Worked great, is clean as there were no leaks under the truck. Comes with the shifter too. $250 located northeast PA. A perfect candidate in which you can install the lower/higher gear sets while your truck is...

· FOR SALE - 3UZ ENGINE 5 SPEED : $2950 1 x 3UZ 5 SPEED ENGINE - ALL WIRED UP AND RUNNING FOR AUTOMATIC APPLICATION 1 x ECU - Immobilizer has been bypassed and flashed. 1 x OEM Wiring harness system which is all wired up for automatic application - Just 3 wires to connect to make it start. 1 x...

I could use some troubleshooting suggestions. I recently got my '76 FJ40 back on the road after a frame off resto. Because the heater and blower still needed to be restored, I initially bypassed the heater valve. My engine has never come up to normal operating temp. The gauge barely comes off...

A few weeks ago, while off road in Anza Borrego, my 1997 FZJ 80 failed to start after short stop. It cranked ok, fired and then coughed and died. Subsequently cranking it produced no firing at all, just cranking away from the starter. After 30-40 seconds of additional cranking it did finally...