I have seen there are a couple of EPS systems out there - Cityracer has an FJ40 specific version which looks very nice, but is a little over my budget at this point.
Has anyone attempted to roll their own using a Toyota or Kia ESP unit?
Search bought up a nice how to from @wngrog on the...
Cleaning up the hood, the center rib looks like it is glued on? As I see no evidence of spot welds. Would seam caulking material be appropriate, after cleaning and derusting?
I have a brand new in the box Distributor for a 1997 Series 80. Purchased two years ago in case my fix on the distributor seal leak did not work. The seal fix worked, so I do not need this.
DISTRIBUTOR ASSY Genuine Toyota (1910066020) - Amayama
Shows a price of 450 + shipping.
Will sell for...
Driving during some heavy rain over the last few days, kept hearing a sloshing sound as I pulled to a stop or accelerated from a stop ( if you can call it accelerate). Thought perhaps the doors as the window seals are not good. Checked the drain holes and all doors dry as a bone. It was the...
While attempting to get my truck started, having previously removed and cleaned up the distributor. I did find some white paint on the BB. I know some folks have a hard time finding the BB.
it looks like I put the distributor rotor in 180 degrees out. Which is why it would not start…DOH
the...
Does the fuel elbow by the tank go through the grommet, or does it stay all on the top side. Looking at this the highest point seems like it would reduce the amount of gas available? Or does the line being full of gas make this not an issue and it will siphon.?
97 Series 80 Land cruiser with 350k miles.
got this code a couple of days ago. I had replaced all the small vacuum hoses as part of baseline, but there was some larger diameter hoses that were not replaced. After replacing the 7mm? Hose between the VSV and the EGR, and 50 or so miles of...
I currently have a Koenig Iron Works PTO winch, which was installed by a previous owner. Badly. There is so much that is needed to bring this up to any sort of standard
Thoughts on bringing this up to scratch or simply removing it?
I just drained and pulled the gas tank to discover there are no rubber pads, is this normal? The tank has been painted on the outside and while there is a small amount of surface rust inside, not worth doing a lining, in my opinion.
I will derust and paint the floor and replace all the hoses and...
I do understand a circuit diagram, but this drives me nuts and need some advice.
obviously the big wire direct from the battery,
the 12 gauge or perhaps 10 Black/White tracer from the ignition switch
but then I have this Black/Yellow from the starter to the coil. Although I this case it starts...
Not yet ready to rebuild my steering box, but in the interests of replacing all the tie rods and the rag joint, thought I should at least change the steering box oil, 0.6qt of 90W oil. Removed the steering box with the pitman arm attached, you can get it out without removing or at least...
Folks, as I work my way through cleaning things, I have four connectors on the fender and I cannot figure out what they are, or need a confirmation on what these are. April76 FJ40 with holly carb and emissions computer/valve deleted
1 pin looks to be LR or LO bit hard to tell May be a throttle...
Folks, want to remove the dash pad, the PO had only 5 screws, every one of them different, took ages to remove them all, but it s not obvious how to remove the dash pad from that point. It looks like it should slide up but will not budge. Suggestions and instructions welcome. I don’t want to...
Given the state of my wiring running to the back of the truck, I will be replacing ALL that harness.
it looks to be 16 gauge, does that sound right?
this will include new fuel level sender wiring and reverse switch wiring, which I am assuming is the same 16 gauge.
and this
yes, the battery is...
Can this be removed or otherwise accessed without removing the transmission tunnel cover.
I have some very crusty wiring, and reverse light is not working.
Removed the bezel in preparation for cleaning and came across something interesting.
the bezel is the whitish color, Cygnus white or Wimbledon white, but on the back, I am seeing the beige of the main body color. Is this normal?
Just received the best Christmas present ever, a 76 FJ40 soft top. Bought it a few months back but was sitting in Seattle until the right time to ship it down to Texas.
looks pretty here next to the 97 Series 80, and a real baby in terms of miles, the 80 has 350k miles, and the FJ40 has 71k...