Hey I’m just wondering what is an acceptable amount of air to be blowing out of the oil filler hole. This is a 3b diesel. Mine seems to have a fair bit, but it’s done it since I bought it 6 years ago. I want to say it feels like a hair dryer but it’s not nearly that high, maybe like a heat gun...
Thought I would share this as well, hopefully it helps. Pretty easy fix that anyone can do.
For a few weeks I had the odd intermittent issue of the starter not turning. There would be a loud audible click from the solenoid activating the gear pushing out, but no crank. A simple fix always...
I figured I would share my experience for future people with the same issue, as all my problems are common they just all happened to me at once.
Originally a few weeks ago the heater worked fine when suddenly I lost speeds 1-2. 3-4 worked fine so I just left it as a future me problem. Later when...
The little tombstone shape door locks in my bj60 rattle incessantly. Drives me nuts:bang:
Has anyone figured out how to tighten them up? Wedging folded paper in against them works for a while.
So I just followed I think Greg’s Wilson switch instructions where I ran power off the glow light to a NO push button and then down to the higher voltage side of my superglow harness, as well as a line going to the glow light which the other side goes to ground.
Superglow system is still...
ok after doing some research and some testing I think my problem is unique enough to warrant a new post. since last summer my bj60 12v 3b has been starting really rough. takes a couple times letting the glow plugs warm up for a good 10 seconds or more and a couple tries of turning it over for...
So my edic controller is cycle clicking causing the motor to hiccup, except mine only does this when the driving lights are turned on. How would those two be connected? What should I be looking for here?
hey there, a new problem just came up on my land cruiser, 84 bj60. its an interesting one that i think will be easy to fix. first time driving it in the dark for a little while, I turn on the lights and I hear this relay in the right side kick panel clicking for a second and then off for a few...
Hey guys, my Bj60 with 230,000km is running into a transmission issue. I just finished a 2300km road trip, and I started to notice a vibration while cruiser at certain rpm, pretty mild, like a stranger wouldn’t notice at all, but when you drive it all the time you notice subtle changes like...
The clutch on my 84 Bj60 has an issue where as I’m letting it out it gets kinda stuck near the top, almost like my shoe is caught on carpet (It isn’t), and then it releases all of a sudden. Makes the Clutch pop and the action all jerky. I took the master cylinder off and it still does it, pushed...
So my 60 series had to go for an out of province Inspection, which is pretty rigorous. One of the items they failed me on was the seat belt buzzer and light did not come on. So I’ve done some diagnosing and trial and still having trouble...
Dash warning bulb was out, so replaced, works...
So I failed my out of province inspection on a couple small points, rear drums out of spec etc, one of them was the drivers seat belt, it’s supposed to be on a switch so the light in the dash and maybe the buzzer comes on. I traced the wire from the seat belt to a single wire clip behind the...
Made in South Africa!
1.3m wide 2.1m long
Incredibly tough 400g poly cotton canvas body (most Chinese built are made of 280g)
Fly is made from a thick pvc that it totally bomb proof, doesn’t flap in the wind, doesn’t let light through.
Annex is also made with 400g canvas.
Big windows, nice...
Front passenger side, in brown. In decent shape except i used the seat cover, but everything else should be there, going in the garbage if no one wants any of it. Located in calgary Alberta, willing to ship at your expense
I’m in the process of replacing the pre-cups on my 84 bj60, and the new cups have a slightly smaller opening. Anyone have info on why this might be and what affect it will have? better starting would be nice as it gets cold here in the winter -30 Celsius.
I put in a new clutch on my 84 bj60 and I’m all done and I have a few extra bolts, wondering if you guys can guess where I missed. I’m mostly worried about the two fatter bolts in the picture. They’re the same diameter but shorter than the 4 transmission bolts and the bell housing bolts.
I’m...
Hey I’m hunting down a gasket set for my 1984 bj60. I’m doing the precups so all I really need at the moment is a head gasket and maybe a valve cover gasket. However I figured I would buy a full engine gasket set so that I have whatever I may need in the future. I want true oem Toyota gaskets...
I’m looking at getting a digital multi gauge to add to my bj60 with the 3b. I want to cover all things like oil pressure, coolant temp, battery, egt and whatever else you can think of on one small gauge. I plan to tuck it at the bottom of my dash.
i specifically don’t want tons of separate...