Search results for query: *

  • Users: kcjaz
  • Content: Threads
  • Order by date

Forum search Google search

  1. kcjaz

    eimkeith PCK available

    I have new Panhard correction kit I bought from @eimkeith a few months ago intending to install it on my new 200 but ended up swapping the entire rear axle which already had a PCK welded on. I have no use for it and it will just sit on a shelf doing nobody any good. It made a very...
  2. kcjaz

    Rubber grommets for front parking sensors (TJM bumper)

    I'm wanting to remount my front parking sensors in my TJM bumper using rubber grommets to hold them in. Dissent does this with the rear bumper but the holes are smaller and their grommets won't work on my TJM. The TJM holes are 25mm (1"). Unfortunately, I didn't bring a sensor with me when I...
  3. kcjaz

    AC fill/gauge connection cap

    I noticed that this cap was just sitting in the fill connection because I knocked it off while working on something else. It won’t screw on. I think it’s supposed to thread on the inside with the o-ring sealing it from dust/dirt. The threads won’t start. Maybe plastic threads are stripped...
  4. kcjaz

    Is there something missing here?

    What should be bolted to this threaded hole (red arrow)? Passenger side near starter.
  5. kcjaz

    Coolant leak diagnosis

    I have noticed a coolant leak around the transmission after having done a lot of work on my new to me 2015 200. You can see what I've been up to in my Build Thread, but short of it is that I have swapped transmissions and transfer cases and all of the front mounted engine accessories between...
  6. kcjaz

    Need help with LRA wiring

    I have had my 24gal LRA moved from my old 200 to the new one. I did not personally do the install either time so I don't know what the wiring at the tank actually looks like. Here is the diagram from the install instructions: My current issue is that the pump does not run and I do not have...
  7. kcjaz

    How to remove “sombrero” from grill?

    I wanted to swap the sombreros between to grill to get the better one on my truck but I ended up breaking the plastic pin trying to pry the retainer off. Clearly there must be a non-destructive technique to do this. Anyone know it?
  8. kcjaz

    Did this 200 belong to someone here?

    https://www.copart.com/lot/67907743/salvage-2015-toyota-land-cruiser-ca-rancho-cucamonga I'm about to auction mine off at Copart and would like to talk to the owner of this if selling on a "public consignment" basis to compare notes. I suspect that this is more likely a salvage vehicle running...
  9. kcjaz

    How can I tell what OME front strut this is?

    the sticker on the strut says "OME-703X" which I think is just the spring and the "X" means its one of several 703's. From googling, it seems that these springs are sold separate from the shocks which is unlike my BP-51s which came as a complete coil over unit. I don't find anything on the...
  10. kcjaz

    VSC dash light won’t turn off

    So my VSC slip indicator is on all the time now. Not this isn’t the “VSC off” icon. It’s the “system is actively doing hill assist of trailer stability. I’m not moving and the light is always on. This is on my 2013 and I have done a lot of rewiring it back to OEM which has involved moving...
  11. kcjaz

    Filling door panel holes - how?

    So I've ordered a set of Rhinohide Armor panels and they will not work with the stock lower door trim panels. My options are trim the Rhinohide panels or pull the OEM lower trim panels off. If I do the later, I'll be looking at this: So how to best fill the holes? There is no easy access to...
  12. kcjaz

    Anyone tow a 200 on a trailer with a 200?

    I want to do this but I technically can't rent a U-haul car trailer rated for the full 5765 lbs of curb weight for a stock 200. The typical rental trailer is max 5290 lbs. payload. I can find commercial trailers rated for 10,000 lbs but then the weight of the trailer plus the 200 puts me over...
  13. kcjaz

    How to determine which OME rear springs I have?

    I have taken off the OME suspension that was on my new to me 200 swapped my BP-51 on it. I’m going to sell the rake off parts but I don’t know exactly what rear springs these are: 722X? My guess is 7220 or 7222.
  14. kcjaz

    Anyone removed Kaon Shelf captive nuts & retainers?

    Swapping my Kaon shelf over to new truck. I don't think I can get the black retainer clips off without mangling them. Anyone done this? I may just have to get new hardware from Kaon.
  15. kcjaz

    Anyone running Dissent RR and a large 270 awning with Fabulous Fab snorkle?

    I know, pretty specific configuration. I'm pretty sure my FF snorkle will clear the Dissent RR as that has been covered in another thread. What I'm trying to determine is if I go with a Bush Co 270 styple awning on the passenger side, will I have any interference with the snorkle? From pics...
  16. kcjaz

    De-pinning front camera connector for ARB camera relo kit

    I've done this once but don't remember how I did it. I'm pretty sure there is a thread here that explains how or maybe someone answered this quastion the first time I did this. I don't see any pin locking mechanism on the OEM connector. I think it is just a matter of pulling the pins out by...
  17. kcjaz

    Replacing Rear Main crankshaft seal - what parts are needed?

    Getting ready to swap transmission/transfer between my 2013 and 2015 200s. Why? See my build thread. While I'm in there (my favorite words), I figure I might as well replace the rear main on the 2015. Do I need anything more than the seal itself (p/n 9031195013)? There is also a rear seal...
    • kcjaz
    • Thread
    • 200 series cruisers crankshaft rear main seal vehicle tech
    • Replies: 1
    • Forum: 200-Series Cruisers
  18. kcjaz

    Front fender liner fasteners

    The front parts of my front fender liners were trimmed to clear larger tires on my 2015 and they won’t work with my TJM bumper I’m moving over to the 2015. The liners are in two pieces and attached by plastic “rivets” that appear to be single use. Are these single use rivets or is there some...
  19. kcjaz

    How to remove door panel molding 2013-2015

    I want to remove the lower door moldings on all 4 doors. I found this good video in @brandonb4 's chrome delete thread but it is for MY 2016+. My 200 is a 2015 and the moldings are different. I do not know for sure if they are clipped on in a similar way or not. I have heard that some MYs...
  20. kcjaz

    Help with TJM T13 install (MY 2015)

    Moving my TJM over to new rig. I didn’t do the original install. Anyone got a pic on how to trim this driver side air guide? The original installer apparently couldn’t figure it out either as the whole thing is just missing on my 2013.
Back
Top Bottom