For Sale [WV/VA/MD] Engines,Wheels,Seats, soft top and more

[huminajumina]

[WV/VA/MD] FJ40 1F 2F Engines,Wheels,Seats, soft top, seats +more

Hey guys I have listed things before with no luck...I have a '68 FJ40 that I have several parts from and more
I will accept all reasonable offers, don't be afraid to make one, trades may be good too, shipping can be arranged for almost anything:

-Black Steel wheels 15 x 8 (Set of 4) No curb/Rock rash or ding/dents $150 (I am not sure of offset or centerline, but can make some quick measurements if needed) 6x5.5 cruiser bolt pattern

-F135 engine with original carb, air filter, siamese manifolds, complete/together...bad compression on #3 cylinder.... $300
-2F '76 2F complete all original parts, bad compression on #3 cylinder, head was removed, all parts together, brand new $200 oil pan and $99 asain oil pump installed.... $300 (as stated it has the brand new $200 pan & $99 pump)

-'68 radiator, small seep at top tank $30

-'76 radiator support $15

-'68 3-speed floor shift, possible for sale $150
-'68 all original seats, 60/40 front and both jump seats $200

-newer BESTOP soft top wiht all frame and windsheild tracks great condition $400

I will list all other parts as I remember them
I am trying to be fair I can provide more pictures and descriptions and once we get closer to a sale I can talk on the phone....I hope my prices are accurate, and I just want to re-coop a little money to put into an engine and trans to get my FJ40 back on the road!!!!
I am willing to trade for most things related to a GM350 swap with NV4500 retaining my '68 vaccum shift TF case....
This is the best I can do for photos right now, but as I said if anyone gets serious I can e-mail some better pix....this is a facebook album, let me know if it works:
https://www.facebook.com/media/set/?set=a.943115452169.2538435.25816556&type=1&l=4acc672378

For any questions e-mail me at huminajumina@yahoo.com, that way I can reply faster and while at work...
2F Block: [URL="https://forum.ih8mud.com/picture.php?albumid=2306&pictureid=25629"][/URL] Wheels: [URL="https://forum.ih8mud.com/picture.php?albumid=2306&pictureid=25631"][/URL]

**I understand prices are Highly Recommended, and Should be included, and should be Individually priced...... I am trying**

This Almost Partout posting is my basement, and I would like to get everything out of the way so I can roll my motorcycle out....
Parts are either from my '68 FJ40 with F135 engine 3-speed on the floor or a
'76 2F 4-speed
list includes but is not limited to:
from '76 2F 4-speed:
flywheel, Clutch, Pressure Plate $35
throwout bearing, pivot, arm $20
Bellhousing *with free mounts* $35
Mechanical Throttle linkage and pedal $25 (may be scattered in pix)
Air Pump $30
bellhousing lower metal shroud $15
radiator support $15
piece of exhaust pipe and bracket that is separate from it free??
Slave Cylinder $3

From '68 F135 3-Speed
Starter motor(works great gear kinda worn, free new gear comes with it $35
Heater duct $15
Rear hatch rusted at bottom/solid at top $20
latches for rear hatch $15
Radiator(seeps where tank meets cores) $30



Anything not listed is $0.01-$50 or best offer.....

 

[85fjmule]

How many rims do you have I'm interested in steelies for an fj60.

Mike

 

[Bang Bang]

Link works but per forum rules you need prices.

 

[huminajumina]

Softtopper sold!!

 

[huminajumina]

I can send pics of most of the parts, just went through some of it. I have both a 3-speed & 4-speed bell housing & both of the engines are complete with flywheels starters & clutch/pressure plates.... I may start parting them out if no one is interested in a complete 76 2F or 68 F135

 

[huminajumina]

BUMP: New pics added, feel free to ask about anything, I have a lot of parts laying around that I am trying to get out of my basement

 

[huminajumina]

Part Pix

**Seats are Sold**

Here are my 1968 FJ40 original seats, the drivers and both jump seat frames are in great condition, the passenger bench has the rust under it from sitting on the gas tank....

 

[huminajumina]

Here is a picture of the F135, I am selling it complete or parting it out depending on the interest, I just pulled it when the #3 cylinder lost compression, its still together and complete

 

[huminajumina]

Someone buy something!! If anyone wants to stop by the house and fill a box up with parts we can negotiate a price....

 

[rkymtnflyfisher]

How about the mechanical parts from the hatch? Does the lock tumbler work fine, and do you have the key? I may be able to swing by and take a look at some engine related stuff also.

 

[huminajumina]

as for the hatch the only mechanical parts I have are the latches on the side, this hatch has that plate to eliminate the handle, I ended up getting another hatch for mine and bought every piece one at a time. The Engine related items are at the shop in Harpers Ferry, WV and all of these things are here in my basement, just let me know when is good for you!

 

[rkymtnflyfisher]

Pm sent

 

[huminajumina]

Dang, Ya'll buy this dang ol engine......

I have this F135 engine for sale, no it isn't the Pratt & Whitney vectored thrust F135 engine, but you should buy it anyway.......

 

[huminajumina]

I could use a NV4500 Bellhousing about now, just saying....

 

[huminajumina]

is there anything I can do to help sell any of this stuff, or is it just all junk? am I doing something wrong here?

 

[dkdnt232]

Pm sent

 

[dkdnt232]

Your pm is full!!!

 

[huminajumina]

Thanks, for the heads up, I just cleared it out, I guess I need to buy a membership

 

[huminajumina]

I'll try to get some better pix today, anyone see anything that they want a close up of?

 

[rkymtnflyfisher]

I'm going to try for next Saturday to swing by and take a look at some stuff. I'll hit you up later this week, let me know if that will work out for you.