What are you working on?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

davidp14 said:
View attachment 3821346

Having the upper intake off makes it not so bad to get the filter off but the back bolt is still a bitch. It's all I have left it so but I quit because it's 19° and I can't feel my toes or fingers anymore
Click to expand...
All that to change the fuel filter !!! haha there are easier ways....:)
 
So dang cold!! Still have a hole in the roof of the 62 and need to test out new rear springs on the 100 to see if I can lower it a bit. Not to mention pulling the engine/tranny on the 62. Looking forward to the spring lol.
 
FamilyCamper said:
So dang cold!! Still have a hole in the roof of the 62 and need to test out new rear springs on the 100 to see if I can lower it a bit. Not to mention pulling the engine/tranny on the 62. Looking forward to the spring lol.
Click to expand...
Warming up this weekend 😎
 
JohnVee said:
Who sells that? It'd be nice to stop replacing the silver tape every season!
Click to expand...
I will have to look it up. I will sell it cheap if you want it.
 
Big thanks to @Land Shark for stopping by this am. We were able to get the rear diff swapped out. ARP hub studs installed and back together. Draining the front and plan to tackle that in the am.

Note: leg goes numb from knee down wearing magic leg! had to stop and take a few breaks. Little work stool amd lift lowered worked great.

Also want to shoot out to @Beach80 who offered help this afternoon. I do not want to push too much in one day as my foot is still sore. Hope to have it all wrapped up by next weekend.

IMG_1656.jpeg


IMG_1655.jpeg


IMG_1654.jpeg


IMG_1652.jpeg


IMG_1653.jpeg
 
Last edited:
matzell said:
Big thanks to @Land Shark for stopping by this am. We were able to get the rear diff swapped out. ARP hub studs installed and back together. Draining the front and plan to tackle that in the am.

Note: leg goes numb from knee down wearing magic leg! had to stop and take a few breaks. Little work stool amd lift lowered worked great.

Also want to shoot out to @Beach80 who offered help this afternoon. I do not want to push too much in one day as my foot is still sore. Hope to have it all wrapped up by next weekend.

View attachment 3824279

View attachment 3824280

View attachment 3824281

View attachment 3824282

View attachment 3824283
Click to expand...
Nice work boys!!
 
got new headlights installed on the Rav 4 and a much needed oil change. Hoping to test new springs on the 100 tomorrow afternoon.
 
Some interesting sway bar link angles happening lol

IMG_4354.jpeg


IMG_4357.jpeg
 
Slow things happening today. Only got a short time out today. A lot of good stuff from Marlin to go in and some other goodies.

IMG_1657.jpeg


IMG_1658.jpeg
 
More ARP studs for front hubs and steering arm. And some Nut Huggers to keep the steering arm nuts tight :)!

IMG_1661.jpeg


IMG_1660.jpeg


IMG_1659.jpeg
 
Stock Size and dowl pins. Just upgraded to ARP studs.
 
matzell said:
Stock or extended length?
Click to expand...
Extended length but I extended maybe an inch longer than Trail tailor and so maybe it was too long. Potentially upon compression it bent and as the end result there is a shorter S shaped link.
 
One more side apart. Not sure these have ever been opened up. Well passed due for service.

IMG_1670.jpeg


IMG_1669.jpeg
 
You must log in or register to reply here.

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom