Trail Tailor Offerings- Racks, Sliders, Control Arms and Misc (2 Viewers)

[TRAIL TAILOR]

All shock guards, antenna mounts and CREEPER skids have shipped! Thank you all for the continued support and patience.

1st of 3 rack loads delivered by the coater today! I have 3 powder and 3 bare left in stock now.

Jason

 

[neckbone]

Just got the antenna mount in today. Need to make a slight adjustment in the angle to make sure the hatch doesn’t scrape it as I close it.

I do have one recommendation if you make more. At the outside corner where the weld ends, throw a grinder on it and knock the sharp corner down. I don’t plan on putting a light on it right now and if someone’s shirt or arm catches that corner, that’s a major gash waiting to happen. I’m going to knock it down myself, but might be good as your making them. Other than that, awesome piece of work!!! Thanks a ton, Jason.

 

[atnolan94]

Got my antenna mounts. I plan to procure some pods to mount. On them in addition to this little CB antenna.

 

[neckbone]

This corner.

 

[fj80psi]

Did he decide if he's going to color match it or not? I thought I saw him mention being undecided awhile back. Bumper looks amazing by the way!!

I’m going with Body color on the bumper and have the new Headlamps apart now so I can spray the inside of them and the new Grill satin black. I have a BiXenon HID setup for the outside lamp pocket and a LED High/DRL setup I. The works.

 

[ERMB]

I’m going with Body color on the bumper and have the new Headlamps apart now so I can spray the inside of them and the new Grill satin black. I have a BiXenon HID setup for the outside lamp pocket and a LED High/DRL setup I. The works.

Very much looking forward to seeing the end result of this whole project!

 

[atnolan94]

Jason, I know these antenna/pod mounts are stainless, but would you still recommend painting them?

 

[TRAIL TAILOR]

Jason, I know these antenna/pod mounts are stainless, but would you still recommend painting them?
[/QUOTE

I made them from stainless so the powder/paint didn't have to be removed for the CB users. Absolutely paint or powder at will!

Jason

 

[TRAIL TAILOR]

Creeper skid and rear shock guards installed!

LX470 UCAs (AHC hardware bolts right up, no zip tie on these arms)

These are going out to @caslim

 

[Kabanstva]

Those shock skids looks great on there with the powdercoat!

 

[TRAIL TAILOR]

Those shock skids looks great on there with the powdercoat!

Just Rustoleum "Sunrise Red" paint. that way I can touch them up when needed.

J

 

[TRAIL TAILOR]

@VidereStudios dropped by yesterday afternoon to grab some parts and talk about some rework on his BIOR rear bumper.

Always good to meet Mudders.

J

 

[TRAIL TAILOR]

Next up, high clearance radiator to diff drop skid plate.

J

 

[abuck99]

Creeper skid and rear shock guards installed! LX470 UCAs (AHC hardware bolts right up, no zip tie on these arms)These are going out to @caslim

View attachment 1928192

That plasma table is sweet- does a super nice looking cut. Bet that was a good investment- they aint cheap.

 

[atnolan94]

Jason, I’m mounting these up and having the same issue as some others where they are a little close to the hatch. I have the resources to reshape them a tad but maybe just something to keep in mind on the next run. Otherwise really great. I plan to get some 2” pods to run as quasi-camping lights.

Also if anyone is curious this a a 24” pro stick from amazon on a firestik spring. Looks absolutely perfect!!

 

[TRAIL TAILOR]

Jason, I’m mounting these up and having the same issue as some others where they are a little close to the hatch. I have the resources to reshape them a tad but maybe just something to keep in mind on the next run. Otherwise really great. I plan to get some 2” pods to run as quasi-camping lights.

Also if anyone is curious this a a 24” pro stick from amazon on a firestik spring. Looks absolutely perfect!!

View attachment 1928705

View attachment 1928706

View attachment 1928707

Check your reveal opening on both sides of your hatch (body to hatch opening) Mine are perfectly aligned (I re-aligned my hatch before I bent the mounts for this very reason), but most I've seen pics of or in person are cocked to one side or the other. Gap should be approx. 1/4" on each side. Antenna mount is .140" thick. My 100 is a repaint (thick paint) and I have plenty of room on each side.

Easiest way to "reshape" if you feel the need (instead of re-aligning the hatch) is to install the mount loosely and put a thin screwdriver/similar between mount and body and push out toward the quarter panel and it'll give a little more bend.

J

 

[atnolan94]

Check your reveal opening on both sides of your hatch (body to hatch opening) Mine are perfectly aligned (I re-aligned my hatch before I bent the mounts for this very reason), but most I've seen pics of or in person are cocked to one side or the other. Gap should be approx. 1/4" on each side. Antenna mount is .140" thick. My 100 is a repaint (thick paint) and I have plenty of room on each side.

Easiest way to "reshape" if you feel the need (instead of re-aligning the hatch) is to install the mount loosely and put a thin screwdriver/similar between mount and body and push out toward the quarter panel and it'll give a little more bend.

J

Makes sense. It’s catching my hatch on both sides, however. So I will try to reshape.

 

[TRAIL TAILOR]

Makes sense. It’s catching my hatch on both sides, however. So I will try to reshape.

This is the gap on mine (both sides) and one other I installed on this week.

J

 

[neckbone]

I put mine in a vice and just used my hands to bend it a little. Fits perfect now.

 

[atnolan94]

I put mine in a vice and just used my hands to bend it a little. Fits perfect now.

That’s my plan. Sorry J not dogging you, it’s an awesome piece. I think everyone’s fit in going to be be ever so slightly different so don’t be afraid to do a little bending.

Thanks again Jason, seems like the 100 is getting a lot of love right now!!