Have any of you mounted a 9100 in your GX460? If so, where did you elect to mount the switch panel inside of the cabin? The 5th Gen has a great custom built panel for the left side of the steering wheel that SDHQ offers and others like the Tundra have snazzy overhead sunglasses compartment mounts or cutouts near the console shifter, but I’m not seeing anything offered commercially for the 460. So where are y’all mounting them or hiding them?
Switch Pros 9100 (1 Viewer)
- Thread starter Tex68w
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
TX GX460
Moderator
HitchCrack
Supporting Vendor
I put mine in the sunglasses pocket. You can find a picture in my build thread. If you haven’t gotten a sp9100 yet hit me up I can help you with that.
r2m
Richard
I have mine mounted with 3M adhesive backed hook and loop (aka Velcro) mounted on the left side of my steering wheel just below the binnacle.
Out of the way but easy to get to. I thought I had a photo of it on my build thread.
Tomorrow I'll take a couple of pictures and post here while also updating my thread.
Out of the way but easy to get to. I thought I had a photo of it on my build thread.
Tomorrow I'll take a couple of pictures and post here while also updating my thread.
r2m
Richard
Here are some photos of where my modular switch panel is located.
I used 2" hook and loop (Velcro) for attaching. Never have had an issue yet.
It's not plainly visible from my seated position (see photo below) as it sits behind the steering wheel and turn signal stalk. But for me, I don't mind and it's not a hassle to move my head a little to see which button I push, especially when I know where the position of the buttons by feel are for each function: air compressor, front locker, rear locker, lights, etc.
View attachment 2579497
View attachment 2579501
The below photo is with it pulled off from the "fuzzy" Velcro.
View attachment 2579498
This is my view with the camera sitting on my nose to give a perspective of my actual view in the drivers seat.
View attachment 2579500
I used 2" hook and loop (Velcro) for attaching. Never have had an issue yet.
It's not plainly visible from my seated position (see photo below) as it sits behind the steering wheel and turn signal stalk. But for me, I don't mind and it's not a hassle to move my head a little to see which button I push, especially when I know where the position of the buttons by feel are for each function: air compressor, front locker, rear locker, lights, etc.
View attachment 2579497
View attachment 2579501
The below photo is with it pulled off from the "fuzzy" Velcro.
View attachment 2579498
This is my view with the camera sitting on my nose to give a perspective of my actual view in the drivers seat.
View attachment 2579500
I made a bracket out of sheet metal and have it wedged into the roof console.
- Thread starter
- #9
Nice! This is very similar to the one that Treaty Oak is working on. How hard was it to run wires under the headliner?
r2m
Richard
That's a clean setup! Did it come with enough wire to run it all the way up there?
I have the Ohana Rig Supply mount incoming
ohanarigsupply.com
ORS DESIGNED - GX460 SWITH PROS / SWITCH PANEL HANDHELD VENT BRACKET
Here we go!!! this panel is designed to help make the cockpit in your rig just a bit more accessible and organized...Formed out of Aluminum to last you a lifetime! This area of the rig has a ton of potential, and this panel will cater to that dead unused space for Switch panels....Doesnt require...
ohanarigsupply.com
I’m currently working on mounting the 9100 control panel into the flip down sunglasses holder. I anticipate that I’ll loose the sunglasses holder functionality, but plan to keep the flip down mirror. Once I finish, I’ll probably write a how-to thread since it seems this is a common issue that we run into with the GX.
