landtank's Upper Rear Links

[Delancy]

I'm not sure what you are talking about.

Apologies. Sent when phone was ringing.

Do you think the rod ends on the your lower links would fit inside the pan hard mount on the axle?

I haven't measured, but know the ones I currently have seemed smaller in diameter, if memory serves.

Edited: More simply.

If a measurement is provided, is a rear pan hard a possibility to have fabbed, too?

Is a front doable?

All in the same manner that the links are, of course.

 

[1973Guppie]

you're all set Noah and there is one person left tat I know of who wants in and then we will go to manufacturing.

At that point I can get an estimate on delivery.

Thanks Rick, appreciate it!

 

[landtank]

Apologies. Sent when phone was ringing.

Do you think the rod ends on the your lower links would fit inside the pan hard mount on the axle?

I haven't measured, but know the ones I currently have seemed smaller in diameter, if memory serves.

Edited: More simply.

If a measurement is provided, is a rear pan hard a possibility to have fabbed, too?

Is a front doable?

All in the same manner that the links are, of course.

I'm not comfortable making Pan Hard bars. There have already been a few failures with the aftermarket ones out there.

I prefer the stock bushings over poly and since there hasn't been a failure that I know of with the stock rods I advocate a DIY joint be used in them.

The joints that I designed are very simple to install and a good welder would make short work of the project.

 

[landtank]

Thanks Rick, appreciate it!

Not a problem.

 

[Delancy]

I'm not comfortable making Pan Hard bars.

Got it. Last I'll ask.

 

[NLXTACY]

Its technically Friday so..... Payment sent!

 

[Delancy]

Its technically Friday so..... Payment sent!

When do y'all sleep?

 

[NLXTACY]

When do y'all sleep?

Sleep? Hold on, I need toGoogle it

 

[Delancy]

Any word on these?

Formulating a plan to cycle and cut fenders, hopefully finish this thing.

Not nagging, just checking for updates so I can schedule accordingly.

 

[landtank]

I got word that the bushings are on national back order. 1 bushing is coming in next week

As far as my end goes, the stock is on order and once in the manufacturing will commence.

I'll let everyone know what is going on once I know. .

 

[NLXTACY]

I got word that the bushings are on national back order. 1 bushing is coming in next week

As far as my end goes, the stock is on order and once in the manufacturing will commence.

I'll let everyone know what is going on once I know. .

Hmm, I DO happen to have spare bushings. Maybe I should send them

 

[landtank]

I'll know more in a week or so. Often the time line I've been given on BO parts has been a worst case scenario and the arrive sooner.

 

[landtank]

just picked up 11 of the 16 bushings that I ordered. So they are coming in quicker than predicted. I'll follow up next week if there is any news.

 

[NLXTACY]

just picked up 11 of the 16 bushings that I ordered. So they are coming in quicker than predicted. I'll follow up next week if there is any news.

Sweet

 

[Delancy]

Any word on these, Rick?

 

[landtank]

The links themselves will be done this week but I'm still waiting on the bushings from Toyota. I'll send an e-mail in a couple of minutes and ask for an eta if they have one.

 

[NLXTACY]

Any word on these, Rick?

Dammit Chris, Rick's got a MAF issue to work out first

 

[Delancy]

Dammit Chris, Rick's got a MAF issue to work out first

So I hear.

 

[landtank]

Really?

I have all the bushings except for 1. Right now my dealership is going through an inventory so I have to wait until next week to get an ETA on the last one.

 

[Delancy]

As long as NLXTACY's are the ones waiting on the bushings, I'm good with that.