For Sale / Wanted To Buy

[dohcdelsol93]

i don't think a 3 speed will bolt up to a 4 speed....but i might not be needing it...i found a pretty good deal on a 2H...will cost a little more initially but will be an easier swap...sucks it doesn't have turbo/won't take boost well...but it's a yota diesel

 

[77cruiser]

60 series Bull bar

I have one that I am going to be removing from my 62 in the next couple weeks. Its in near perfect shape with a couple small surface scratches but nothing thru the powdercoat. I would like to sell it locally for around 650 because I dont have the time or energy to ship it.

Hit me up on the email if interested. josh@jhcustombuilders.com

 

[Cirbo]

WTB 4 speed trans, transfer case, axles

WTB..

I need a 4 speed trans and transfer case in good condition. I am also in the market for '78 or newer FJ40 axles (front and rear).

email me at seriesLR(at)gmail(d0t)com

Thanks,

Jim

 

[Boot]

Listing for a friend.

2006 ZX10r - $5975 (Pendleton SC)

Craigslist link



-Lenny

 

[Boot]

Also I have another friend that is looking for a set of wheels for his '03 Tundra anyone have some laying around?

-Lenny

 

[dohcdelsol93]

have a few parts laying around...I'll offer them up locally first

3F stamped bellhousing (for putting an H55F onto your F series)

extra clutch fork

a clutch/flywheel/pressure plate off of a late 86 or 87 cruiser with supposidly less than 85K on it...the fingers on the p/p have very little wear, i've been told that many of these stock clutchest got from 150-175K on them. I believe it's OEM toyota, if there is a way to verify i would gladly check it. It's all coated in light oil and sitting in my shop to prevent any rust.

Still have two 2.5" over stock hell for stout shackles...still brand new in box! Make offer...i think they are 65 new from the dealer for a set of two.

Also have a H42 and transfer case that i removed from my 86 LC. the tranny i'm keeping to test fit my swap before removing the engine/tranny but the TC i'll sell. The tranny is shot but the TC is probably still good, i would recomend pulling it apart and rebuidling before use since it had 250K on it.

help me fund my swap!!!!

once the swap is in the 2F is up for sale. De smogged, 6-1 one piece header, webber 32/34 (it think) carb on no it, make offer! Had someone interested in it but i think bob is selling off all his projects. So if he doesn't want it (i gave him first dibs) it's fair game!

De veined smog pump, leaky PS pump, brand new alt (will not come with the a/c compressor) but the rest of the engine complete from AF to pan

also the intake fan for sale!

let me know what you need!

 

[dohcdelsol93]

looking for a 62 gas pedal/t.cable assy...want to try locally first....also need a diesel fuel filler neck...i'm betting i'll have to get that one shipped!

also need 62 power steering hoses...don't mind buying those new/getting cline to make some but if anyone has them laying around...i'll take them off your hands!

 

[AGreekBoy]

on your filler neck, you can cut the spot welds off and reweld them. It worked fine for me

 

[AGreekBoy]

If anyone want to buy a Fj cruiser mine is up for sale. I would like to get 25,000. Its negotiable. still under waranty bumper to bumper. Also has 100,000 mile drivetrain transferable warranty from dealer. 23,930 miles.
ome 3" lift
ARB front bumper with winch mount

 

[jleeFJ62]

Congrats on the baby girl!!!!

 

[89s rule]

I am selling my 1995 Yamaha Warrior 4 wheeler I never ride it anymore and could use the $ elsewhere. I have owned it for 6 or 7 years. Pics on the way.

Asking $850. Possibly consider a trade for a dual sport bike.

 

[AGreekBoy]

Congrats on the baby girl!!!!

Thanks man sorry i missed you today at lunch

 

[dohcdelsol93]

on your filler neck, you can cut the spot welds off and reweld them. It worked fine for me

so just get a fuel neck from any given diesel fuel neck and weld it in place


great idea...thanks!

 

[AGreekBoy]

so just get a fuel neck from any given diesel fuel neck and weld it in place


great idea...thanks!

No, use your original filler neck. There are 3 spot welds on it cut them and reweld the holes. It worked for my 60 just fine.

 

[dohcdelsol93]

have a late 86/87 h42 for sale...comes with tranny and tc...i'll even throw in the bellhousing!!!!

po told me it came from a rusted out rig up north about ten years ago and has less than 85K on it..i've put 5K on it

the clutch i pulled of of the flywheel that went to it looks barely broken in and the way it shifts/runs i have no doubt it's low mileage.


I'm putting in an H55 (ditching the ranger OD route) and i was going to keep it for a good spare but i could use the cash to pay for the project

paid 500 for it in the spring....asking 400 for it. It's still in the vehicle...you can test drive it if you would like.

 

[Southeast Overland]

M716 trailer for sale

No longer for sale.

 

[Gundy]

I'm selling my M716 trailer b/c I just bought another trailer. The M716 is basically a flatbed version of the American M416, or Canadian M101. I'm giving first dibs at this to UC members. Here is some info.

- 3/4 ton trailer
- Tires are in good condition which is nice b/c they can be pricey - it has very stiff sidewalls. When I bought the trailer there was zero air pressure, yet I was still able to easily pull the trailer about 5 miles to a gas station without any trouble
- Pulls straight as an arrow, doesn't bounce
- Pintle hitch, could be modified for a ball hitch but the pintle is more maneuverable
- Parking brake works perfectly (i.e.: when you set the parking brake the trailer will NOT move, the tires lock up tight
- Front 'stand leg thingy' works great, folds out of the way nicely
- I have never attempted to use the lights
- Frame, axle, wheels are solid, IIRC the bed has one rust through spot about the size of a quarter
- Original paint in lots of places, good bit of surface rust too
- PO installed some wooden sides, I had planned to cut these off but they are still there
- PO installed wooden tailgate pulls up and detaches

My original plans had been to simply sandblast, repaint and install new bearings and use her camping.

First $300 takes her.

Good thing that Pig is set up for a pintle/lunette.

 

[Southeast Overland]

Good thing that Pig is set up for a pintle/lunette.

The cat is out of the bag!

 

[Boot]

I'm selling my M716 trailer b/c I just bought another trailer. The M716 is basically a flatbed version of the American M416, or Canadian M101. I'm giving first dibs at this to UC members. Here is some info.

- 3/4 ton trailer
- Tires are in good condition which is nice b/c they can be pricey - it has very stiff sidewalls. When I bought the trailer there was zero air pressure, yet I was still able to easily pull the trailer about 5 miles to a gas station without any trouble
- Pulls straight as an arrow, doesn't bounce
- Pintle hitch, could be modified for a ball hitch but the pintle is more maneuverable
- Parking brake works perfectly (i.e.: when you set the parking brake the trailer will NOT move, the tires lock up tight
- Front 'stand leg thingy' works great, folds out of the way nicely
- I have never attempted to use the lights
- Frame, axle, wheels are solid, IIRC the bed has one rust through spot about the size of a quarter
- Original paint in lots of places, some surface rust as seen in the pics
- PO installed some wooden sides, I had planned to cut these off but they are still there
- PO installed wooden tailgate pulls up and detaches

My original plans had been to simply sandblast, repaint and install new bearings and use her camping.

First $300 takes her.

Hmm I wonder if I can sneak this by the wife

 

[$out]

Forsale/ 2000 4runner limited w/ 95k miles. I need a truck so if you know someone let them know. $9500 obo