Final knuckle rebuild video tutorial finished, have a look! (1 Viewer)

[lshobie]

Hi Guys,

I've made the last hub/knuckle/brake etc rebuild video, go here to check it out:

Toyota Land Cruiser front Knuckle rebuild tutorial - YouTube

And these are some of the other videos in my series:

Video #1 Toyota front knuckle, hub, and brake service overhaul Video #1 Removal.

Toyota front knuckle, hub, and brake service overhaul Video #1 Removal. - YouTube

Video #2 Aisin Manual hub (free wheeling hub) rebuild Toyota Land Cruiser

Aisin Manual hub (free wheeling hub) rebuild Toyota Land Cruiser - YouTube

Video #3Land Cruiser rear brake service, shoes, drum, emergency brake adjustment

Land Cruiser rear brake service, shoes, drum, emergency brake adjustment - YouTube

Video #4 Land Cruiser rear hub/axle service, bearings, axle, seals, gasket etc

Land Cruiser rear hub/axle service, bearings, axle, seals, gasket etc - YouTube

Video #5 Slee Castor Correction Bushing install, Land Cruiser Tutorials.

Slee Castor Correction Bushing install, Land Cruiser Tutorials. - YouTube

Video #6 Land cruiser 1HZ 1HDT 1PZ Valve shim adjustment tutorial

Land cruiser 1HZ 1HDT 1PZ Valve shim adjustment tutorial - YouTube

Video #7 Warn 8274 winch rebuild series #1, disassembly of winch

Warn 8274 winch rebuild series #1, disassembly of winch - YouTube

Video #8 Warn 8274 Rebuild video # 2 Re-assembly of winch

Warn 8274 Rebuild video # 2 Re-assembly of winch - YouTube

 

[excessive]

NICE! i was really impressed by the disassembly video, i was waiting the re-assembly!

thank you!

 

[SpillmanCruiser]

Nice Work! Can this be added to FAQ?

Also, are the three screwdrivers used in place of the SST on the rear axle rebuild?

 

[lshobie]

Yes I just use a screwdriver in place of the sst.

 

[SuperHatch]

Great Video!!!

The pads can also be installed while the caliper is actually bolted in place. Can be a little easier that way.

 

[richxd87]

Awesome! Been waiting for the rebuild portion. Thanks!

Richard

 

[hawaiicruz]

excellent resource thank you

 

[Jrob80]

AWESOME VIDEOS

 

[NorCalLC]

AWESOME VIDEOS

X2, thanks for your hard work

 

[Owyhee Jackass]

Thanks, when starting maintenance that's not done so often, it's nice to have quick refresher video to watch before hand. I really appreciate your effort it, makes diving in a bit less daunting.

Dan

 

[lshobie]

Thanks guys, Dan that's true and I even refer to my own videos as well! Helps me remember where everything goes!

 

[Owyhee Jackass]

Just curious why you mention to 'ensure you lock the rear diff. before pulling the short side axle...' in you rear axle rebuild.

The FSM doesn't mention it. I just did this service last night and I did follow your advice, what are the concequences if you fail to lock?

 

[ERG80]

Awesome

 

[landtank]

unfortunately you put things back together wrong.

Working from the spring perch out

Felt gasket
rubber gasket with ridge facing felt
Steel split ring
knuckle housing

From what I've been told, the same mistake was made on the DVD that's out there as well.

 

[Kernal]

IMHO this video is good to get a general overview but anyone who's planning on doing the front axle service needs to read through the FAQ section thread and others on this topic and print out the tools, supplies and torque measurements needed. The video skips some things, like removing the ABS sensor before you pull the driveshaft/birf if your vehicle has ABS. Also the dust shield was left off and the grease used does not look like Moly fortified grease?? Were the birfields repacked?? Wouldn't want a complete newb (like me) to dive into the job without being properly prepared.