Clean solutions for securing water bottles?
- Thread starter eatSleepWoof
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I'm going to post this message again since it got bumped to the last page and I want to make sure folks see this who are looking to swap out their 2008-2015 version for the new 2016+ version. I have the first batch of the new Cruiser 2016+ Cup Holders going into the spray booth this afternoon. They will be cured and ready to box up this weekend and ship out Monday morning. The next larger batch will be getting sprayed on Saturday and will be ready to ship out on Tuesday. The first batch is going out to the folks who already ordered the 2008-2015 toyota version and need the 2016+ version. If you are one of those folks please reach out to me now so I can set up the exchange with you. As soon as all of those folks have been taken care of then the rest will be stocked on our website sometime this weekend. I will let you guys know once we stock the website. If you ordered the 08-15 Cruiser version but needed the 08-15 LX570 version; also reach out to me and we can work on that exchange. I will have a small batch of those ready to ship on Monday as well. For the 2016+ LX570 folks; I don't have anything for you yet. Nobody has stepped up to loan me their console section to work off of. Right now I just need pics of the center console of the 2016+ LX570 so I can compare with the others pics I have of the 2016+ Yota and older LX version.
I finally got a batch of the new Cruiser Cup Holder 2016+ and the new LX570 Cup Holder 2008-2015 versions up on our website. It isn't a very large batch since the first ones had to go to the folks who are swapping out their design for the newer version. I will restock middle of this upcoming week with a much larger batch. The first wave will ship out tomorrow and the rest will ship on Tuesday and into Wednesday.
www.bh3dprinting.com
200 Series Double Cup Holder – BH3D Printing
www.bh3dprinting.com
LvCruiserNewb
SILVER Star
Single flask for 2016+ ordered. This is going to be a life saver. I'm so tired of the old lady's nalgene rolling around in the front seat... And a place to put my phone too. Double bonus...I finally got a batch of the new Cruiser Cup Holder 2016+ and the new LX570 Cup Holder 2008-2015 versions up on our website. It isn't a very large batch since the first ones had to go to the folks who are swapping out their design for the newer version. I will restock middle of this upcoming week with a much larger batch. The first wave will ship out tomorrow and the rest will ship on Tuesday and into Wednesday.
200 Series Double Cup Holder – BH3D Printing
Yeah, got an order in before they sold out!I finally got a batch of the new Cruiser Cup Holder 2016+ and the new LX570 Cup Holder 2008-2015 versions up on our website. It isn't a very large batch since the first ones had to go to the folks who are swapping out their design for the newer version. I will restock middle of this upcoming week with a much larger batch. The first wave will ship out tomorrow and the rest will ship on Tuesday and into Wednesday.
200 Series Double Cup Holder – BH3D Printing
dubyahard
SILVER Star
Ordered a double. Not totally sure if my Hydroflask 18oz. wide-mouth coffee bottle with 2.91" diameter will fit the single flask small size so I just ordered the double and hopefully the inserts will hold it steady. So ready for a solution.
The small hole is 3.1" and the large hole is a hair larger than 3.75".
Markuson
SILVER Star
If you add the available rubber boot to that hydro flask, it becomes perfectly free of movement.
Same with the larger Hydroflasks. Add the boot...fitted perfection. They work fine without the boots, as well...but for the ultimate in movement-free...the boots are great. I suspect they’ll fit various generic brand bottles too...
Last edited:
Time for an update. I intentionally stayed away from this thread to make sure it was not getting bumped back to the top. We released the Cruiser 2016+ cup holder versions and the 08-15 LX570 versions last week and it got CRAZY. I restocked every other day and had to use 20 machines to keep up. I did not expect the LX570 version to be so popular. We got bogged down in orders and got behind. I apologize if you ordered an LX570 cup holder and it didn't ship right away. The last orders for those are shipping out this afternoon. We are finally caught up on all of the orders. We will be restocking the LX570 cup holders tomorrow. The orders that came in yesterday are shipping out tomorrow. Now that the initial rush is over; we should be able to do a better job at keeping them in stock. Again, I apologize to the folks who had to wait most of this week before we shipped. We will be shipping at our normal pace from here on out.
Just got the 2008-2015 LX570 Cup Holders restocked. Hopefully this new batch will at least last through the weekend. The new batch will be shipping out on Monday from any orders that come in over the next few days.
DasKeyserSoze
SILVER Star
Is anyone using the VHB on the bottom of the cupholder unit? I'm concerned that I'll never be able to remove it. . .VHB sticks like crazy!
BTW, here’s a pic of mine installed (2019 LC). I hit it with a light coat of Rustoleum truckbed liner. Blocked the cup openings with some plastic Dixie Cups so the inserts would still fit properly.
Based on the few I have personally installed; I don't think you need the 3M adhesive. It was more there for sound deadening. It prevents the bottom from rattling. If folks want it SUPER secure then they could also use the adhesive as adhesive instead of just sound deadening foam.
Many more LX on the road. It’s an underserved market due to the stereotypes in place around who is owning and driving them and in what way.
There is one for your model. There’s early LC200 and late LC200 then separate ones for the LX570. I have one in my LX and it’s awesome.
Here’s a link that should take you directly to the 2008-2015LC. 200 Series Double Cup Holder – BH3D Printing Hit “Choose an option” to see all the variants.
Last edited:
Just read the last 4 pages of the thread. Pre-apologies, but I have a few questions for my 2013LC:
I want this new holder to swallow a 32 oz nalgene (3.75" wide) - or two if possible.
Does the dual flask option hold two of these 3.75"ers? And the single flask option holds one 3.75"er?
Since the photos don't change on the website when you select a different option, I'm a bit confused.
Also the top cover "door" on the stock cupholders goes away completely when installing this switch I assume. Correct?
Approximate time and tools needed to do the swap? Again, I'm assuming this is a pop out pop in type thing.
Cell phone holder slot looks awesome. Is that not available on the 2008-15 versions?
And lastly - what is the rubber insert people mentioned? Is that included or a separate purchase.
Again - sorry for the confusion on my end and for all the questions. Much appreciate you making these and going through the trial and error to meet needs. Thank you kindly. Excited to try one out once I'm squared away.
I want this new holder to swallow a 32 oz nalgene (3.75" wide) - or two if possible.
Does the dual flask option hold two of these 3.75"ers? And the single flask option holds one 3.75"er?
Since the photos don't change on the website when you select a different option, I'm a bit confused.
Also the top cover "door" on the stock cupholders goes away completely when installing this switch I assume. Correct?
Approximate time and tools needed to do the swap? Again, I'm assuming this is a pop out pop in type thing.
Cell phone holder slot looks awesome. Is that not available on the 2008-15 versions?
And lastly - what is the rubber insert people mentioned? Is that included or a separate purchase.
Again - sorry for the confusion on my end and for all the questions. Much appreciate you making these and going through the trial and error to meet needs. Thank you kindly. Excited to try one out once I'm squared away.
Last edited:
RobW0
GOLD Star
Yes the cover door goes away. The only tools you need are your two hands and it takes about 2 min. The old holder pops out with a good tug on the cover door and then the new one just slides in.
