iptman
SILVER Star
Dang...I would have done that for sure but I posted a WTB thread and got hits almost immediately. Thanks anyway though.
Parting Out 96 FZJ80 In San Diego (12 Viewers)
- Thread starter Bluetribal
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
teleskier
SILVER Star
I need a auxiliary hood catch. It is the part you push on to release the hood when lifting it up. It sits just to the drivers side of the hood lock mechanism.
- Thread starter
- #103
No prob how about $10 and would guess $5 for shipping without looking at it.
- Thread starter
- #104
So I do not have the RS3000 alarm but I did get the keyless entry box removed if anyone is interested in that. I even took a photo of the wires it splices into behind the DS kick panel.
- Thread starter
- #106
You would have to be way more specific on internal wire harness.
But if you are talking about all the plugs for the instrument panel then yes they are all available.
But if you are talking about all the plugs for the instrument panel then yes they are all available.
passenger ac vent, the one closest to the door, is that available? if so, price shipped to 33626
- Thread starter
- #108
Sorry I am selling that with the entire dash.
If you're running 861/862's, I'll take em ... 480.779.8307
- Thread starter
- #110
Axles will be sold with frame and body not parting that far. Need it to roll out of my driveway.
whats the chances you have a transfer case wiring harness
specifically in the picture I attached 82125......
specifically in the picture I attached 82125......
- Thread starter
- #112
Probably pretty good. Just will need to try and figure out the correct wire plug now that the transmission is out.
Give me until tomorrow evening as I need to work on a side job tonight and will not have time to crawl under the truck.
Give me until tomorrow evening as I need to work on a side job tonight and will not have time to crawl under the truck.
- Thread starter
- #113
It is really tough to tell from that diagram. I laid out all my wiring to see if I had that one line with a plug on each end and no luck. I bet it was still attached to the transmission.
- Thread starter
- #114
The Rig just left my driveway on its way out to Desert Hot Springs where the axles will be used under a Samuri and then he will probably sell the body or frame and re-coup his $.
But my work is done and the beast is out of my driveway! I still have parts in bins in the garage and will be closing this thread as soon as I get a full inventory and photos up in the parts section of classifieds.
But my work is done and the beast is out of my driveway! I still have parts in bins in the garage and will be closing this thread as soon as I get a full inventory and photos up in the parts section of classifieds.
Hi, looking for the front calipers and backing plates, shipped to Canada T2E7K7.
Cheers,
Alex
Cheers,
Alex
- Thread starter
- #117
Sorry, caliper and rotors went with the shell since they guy was buying it for the axles.
cool, thanks.
- Thread starter
- #119
I just pulled the Yakima A1 rain gutter towers off of my Yakima bars to change out for new towers for my GX 470.
These old towers were bought used and they are not pretty but they work perfectly.
$60 for all 4 towers + $12 S&H or I will sell individualy for $20 ea.
I also have two locks without a key but they are lock #A145 so you could source a key. $5 each lock.
These old towers were bought used and they are not pretty but they work perfectly.
$60 for all 4 towers + $12 S&H or I will sell individualy for $20 ea.
I also have two locks without a key but they are lock #A145 so you could source a key. $5 each lock.
Do you still have the airfilter canister? No top needed.
