What tires are you looking for Nolen?
60 series....Tech and Classifieds (1 Viewer)
- Thread starter Bomar
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
What do you mean what tires? I am not looking for tires.
Misunderstood legs for shoes on the $2500 comment.
Last edited:
Flat towing a 40 with terrible caster with a 60 with no power.
Bad idea of bad ideas.
Bad idea of bad ideas.
Bodean
Hot Damn
You did that the year I met you at GSMTR didn't you Nolen?
Yeah. NOLA to GSMTR
It was murder.
McCready. You happy with windshield work? Got my parts.
McCready. You happy with windshield work? Got my parts.
Yes, see below; I think it turned out good. Went through car wash the other day, and drove in the Monsoon this morning and not a weep of water.
I bought this for the body and clean interior, and not the 2F (although it does have low miles). So, going to do a compression test on my engine this afternoon and see if she is worthy of cooling parts and such. Will post up results.
I bought this for the body and clean interior, and not the 2F (although it does have low miles). So, going to do a compression test on my engine this afternoon and see if she is worthy of cooling parts and such. Will post up results.
No. Tires good. Old. Expired but they stay. Hope a rear blows out first.
If that 2F isn't smoking it is probably just fine.
A desmog and JimC refresh will wake it up but there is just so much that can be done with a 125hp motor in a 6000# vehicle
A desmog and JimC refresh will wake it up but there is just so much that can be done with a 125hp motor in a 6000# vehicle
did a compression test tonight, because I was tthinking about putting some miles and upgrades (h55f) on the 2f before ultimately swapping to a v8. Of course cylinders 1-5 were dialed in, if not a bit high but it was more than warmed up when I did it (150 dry; 155-160 wet).
Wet
Cylinder 6 maxed out at 100 dry and 110 wet. My high tech oil injector
I squirted some fogging oil in the cylinder, and got it to move up to 115 and change. Still way off the other readings.
Plugs were all pretty smoked out white:
Changed all those out.
Checked out the air filter while I was noodling around (dirty and will order a new one), and cleaned up after the former residents:
Other than it running warm (and slow), I am not feeling or hearing anything to suggest something bad is going on in there.
(I'll YouTube and post a short vid later of it running).
The good news is that I have standing handshake with lash to buy this one from me, so its nice to have that out in my back pocket
Wet
Cylinder 6 maxed out at 100 dry and 110 wet. My high tech oil injector
I squirted some fogging oil in the cylinder, and got it to move up to 115 and change. Still way off the other readings.
Plugs were all pretty smoked out white:
Changed all those out.
Checked out the air filter while I was noodling around (dirty and will order a new one), and cleaned up after the former residents:
Other than it running warm (and slow), I am not feeling or hearing anything to suggest something bad is going on in there.
(I'll YouTube and post a short vid later of it running).
The good news is that I have standing handshake with lash to buy this one from me, so its nice to have that out in my back pocket
Last edited:
Valve adjustment?
Spend your money on lifts and tires and cool s***.
Caught up with Roger this am. He's the only thing I miss about that period of my life.
His 62 has 132,000 miles. I'm jealous of the paint
His 62 has 132,000 miles. I'm jealous of the paint
Me an' BillRiiiley survived with just lap belts in the back seat, but my wife insists that our kids need shoulder belts and a booster seat.
So, I purchased rear belts and trim pieces (several years ago) from an FJ62, and am finally putting them in.
I used this thread for instructions: https://forum.ih8mud.com/threads/fj62-rear-shoulder-belts-in-fj60.295136/
Here's the driver's side, not yet done, for reference...
And the finished passenger side...
So, I purchased rear belts and trim pieces (several years ago) from an FJ62, and am finally putting them in.
I used this thread for instructions: https://forum.ih8mud.com/threads/fj62-rear-shoulder-belts-in-fj60.295136/
Here's the driver's side, not yet done, for reference...
And the finished passenger side...
Last edited:
I love that the hole is there and the trim is right. Nice job.
Well then....
There are also other nice predrilled holes in the 60 that allow 62 parts to be inserted.
There are also other nice predrilled holes in the 60 that allow 62 parts to be inserted.
What else ya got?
