Trade 3B Parts for Trade

[colby1979]

Location

United States

Hey guys, after 15 years of driving 3B powered cruisers and rat-holling parts it's time for me to let these go. What im looking to do at this point is TRADE the items (part for part or something close to that) for 24V 1HZ spares. Most of the electrical items are 24v except for the edic motor. The alt, starter, fan clutch, glow plug timer, exhaust manifold, tsta housing were removed from a low km (under 100k iirc) motor that I swaped into my old 42. I also have quite a few new items to include 20.5v glow plugs, speedo cable, top end gasket set, tstat, rad cap and new high nickel head from AU with precups installed. The IP and injectors will be traded as cores, I purchased them off ebay as "good running condition" but never saw them run and they will at least need a good cleaning and test prior to instillation. The used head is cracked between the valves so is basically scrap and two of the water pumps were functional prior to removal and the other is toast. I also have numerous small parts that are shown in the photos so please contact me for details as it would take a forever to list them individually. I also have a later 40 series oem 4 row radiator that looks to have been re soldered at some point but a number of the fins are laid over so I would recommend it to be record. There's a ton of stuff I've forgot to mention and I apologize for the haphazard poor quality photos. If you see something your interested is swaping for please shoot me a pm for more details. Also, the thread will be updated as I dig out more parts. Thanks for looking, Colby

 

[colby1979]

More pics

 

[colby1979]

More pics

 

[colby1979]

And some more

 

[Splangy]

Interested in purchasing a power steering pump bracket and LHD throttle cable if you have either.

 

[colby1979]

I'll let you know if I decide to sell. I'm pretty sure there is a throttle cable, not sure about a ps bracket.

 

[Ambrew]

I have nothing to trade really but would be intersted in the head and gaskets if you decide to sell.

thanks, and good luck!

 

[Ivo Ferreyra Vargas]

Would you sell the preheater timer, flasher?

 

[colby1979]

Sounds good, im still hoping for more trade options but will contact ya'll in a couple days if nothing happens.

 

[In2cruisers]

price on 12v edic motor?? working?? trade for $$s??

 

[colby1979]

Ok, ive traded a couple small items but tye bulk of the parts remain. I will now starts selling items (trading for cash). I will also slowly start listing items on ebay as it simplifies payment and shipping.

First off ive had a lot of interest in the high nickel head. I purchased two of these from AU about 10 years ago as I needed one and thought a spare was a good idea. Iirc with shipping they were about 950 each. I will sell this head for 800 plus shipping, this would be an excellent candidate for mudship as shipping will not be cheap and of course local pickup would be welcomed!

 

[colby1979]

Next up is the 12v EDIC motor. I will sell this for 200 plus the ride. The guys at cruiser parts dot net have a used one listed 300.

As far as payment goes I can accept paypal (friend and family only) or USPS money orders and will primarily ship vis usps flat rate priority at actual cost.

 

[In2cruisers]

Ok..thanks brother.....was going to pick up as spare if cheap enough...

 

[colby1979]

Ok..thanks brother.....was going to pick up as spare if cheap enough...

Rgr that.

 

[Ivo Ferreyra Vargas]

Hello, any news on my offer on the preheater timer?

 

[colby1979]

PM Sent

 

[In2cruisers]

Need the two injector line CLAM mounts

 

[Cavalier2000]

The gasket set. Is that a paper type head gasket or metal?

 

[SuperDuperCruizer]

I have a spare cable locking differential to trade... interested in your cylinder head & gasket, thermostat housing, B-series input shaft/bearing retainer and 12 volt parts.

 

[Ivo Ferreyra Vargas]

i have a a bj70 preheat timer...