Splangy
Latest activity Postings About Badges Post areas
-
-
Don’t have a photo right now but FJ25’s shifting instructions and tire pressure plates are on the dash where the later ash tray is. Nothing on the glove box but paint and a Pocket handle. -
Splangy replied to the thread Raptor Liner Adhesion Issues.If it chipped through to the bare metal areas, it’s an adhesion issue between the primer and steel. You may not have actually cut the steel much as you thought with the 120 grit paper. I’m not familiar with the UPOL epoxy primer so I can’t...
-
The difference is mostly in the mounting arm. Later model does not stand out away as much as the earlier models which needed to clear the motor and cables. I don't recall my old 1/79 blades being any bigger than my earlier blades bit it has been...
-
Splangy replied to the thread Wanted FJ25 trans hump.I have one, but it was cut in half and needs to be welded back together.
-
Splangy replied to the thread Parting Out Parting out 2H.Any chance you still have that fan shroud after 4 years?
-
Splangy reacted to chrisspaulding's post in the thread For Sale Greensboro, NC 1990 LJ-78 Project Truck $5900 with
Like.
I purchased this project from @coldtaco back in March 2020. Here is a link to the original ad: https://forum.ih8mud.com/threads/lj-78-modified-no-drivetrain-anchorage-ak.1193509/ I had the truck shipped down from Alaska and it has sat in my... -
Splangy replied to the thread Wanted Looking For 60 Series Rear Brake Backing Plates.Bump
-
Splangy replied to the thread Wanted Looking For 60 Series Rear Brake Backing Plates.Bump
-
Splangy reacted to roma042987's post in the thread SOLD Cable locking differentials for 60 and 70 series models with Like.
Unfortunately, you will likely need unchipped gear sets as well.
-
Splangy replied to the thread Wanted Series 80 Rear Backing Plates.I have a set
-
Splangy replied to the thread SOLD Cable locking differentials for 60 and 70 series models.I believe you’ll need axle shafts with longer splines (at least one side IIRC) and I believe you’ll need a full floater to run these.
-
Splangy reacted to bottombracket's post in the thread SOLD Cable locking differentials for 60 and 70 series models with Like.
OH WOW
-
Splangy reacted to LHDjdm85's post in the thread For Sale Saskatoon - HJ60 JDM - left hand drive with Haha.
'85 HJ60 - 2H diesel - 80% restored - professional conversion to LHD - sun roof - no rust anywhere - new paint (Dodge Destroyer Grey) - no rust covered up - 170 km - stainless steel roof rack with permanent ladder - factory pto winch - factory...
-
tossing it out as i don't think i'll ever get around to it and would rather someone get it out of my barn and on the road bought as a rolling shell, so not at all original. engine is from a wrecked 77. oil pan was toast so clearanced a 1f pan i...
-
Splangy reacted to scoobiedubes's post in the thread SOLD ‘61-‘63 Dual Sided Turn Signals with Haha.
I need to stop staring at these… if only there was a source for a new amber lens
-
Splangy replied to the thread Wanted BJ42/BJ46 Vacuum shift diaphragm.Looks like you have most of the vacuum parts.
-
Splangy reacted to cruisermatt's post in the thread Wanted BJ42/BJ46 Vacuum shift diaphragm with Wow.
I actually found a complete transfer case with one of these on it. I was ecstatic. Of course the box got destroyed in transit and I only ended up with the main case halves. 😥 The front case does have the shift fork/shaft so will post up...
-
None. But, it should be reduced a little if using as a sealer, as it sometimes fails to level out. The SDS for the reducer says it is 80% acetone, which is consistent with epoxies.
-
Splangy replied to the thread Epoxy Primer Odd Behavior.What are you using for a thinner?
-
Yep, which is why I am thankful I found this one to relocate my turbo and be able to install my newly painted hood without having to cut a hole in it. Thanks again @TeamJB
-
Splangy replied to the thread Wanted 12HT exhaust manifold..One’s a turbo manifold and the other isn’t. They will both bolt up to either head.
-
Splangy reacted to sunrk's post in the thread POR15 et al and how to correctly open the tins and seal them back up again with Haha.
POR-15 is awesome stuff. Used it on quite a few things. Currently using it to fully coat a replacement 80 series front diff/axle housing (esp the swivel balls) and the floor of my box trailer. The three-step process works good combined with...
-
These guys advise against painting the mating surfaces as well.
-
Splangy replied to the thread Epoxy Primer Odd Behavior.A few thoughts: 1) Was it mixed properly? Any thinners used? 2) was there an adequate surface profile achieved on the panels? (Sanded peoperly) 3) was the the panel cleaned with the appropriate wax/grease remover prior to application?
-
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…