For Sale 1996 Locked FJ new leather seats, 4x4 labs bumper

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

For sale 9.5k OBO

New pioneer navi/ subwoofer
New leather by shane
New bumper by luke
New brakes all around
Head work done
Matching bedliner
LEDs all around
Ready to roll

extra set of rims and jump seats included.
IMG_0425.webp
IMG_0429.webp
IMG_0430.webp
IMG_0435.webp
IMG_0436.webp
 
Click to expand...
I'll take them (4).
My wife works in PA so pick up should be easy.
Give me a call 464-
 
Last edited:
Factory wheels sold...

The bediner was done professionally by a linex Dealer....I color matched it with the toyota paint.

The holes were filled by me.... I took Metal epoxy and fiberglass screen and filled the holes and sanded then primered...looks great....
 
Had toyota replace the heater box and clean the vacuum within last two years... All new rotors and new pads within last 3 months..New tires less than 300 miles on them...

Possibly sold, Taking back up offers...
 
BRob2756 said:
Sure. Four 0 4- Five two 0- 02five nine . Call anytime. Thanks!

Rob
Click to expand...

There is a lot... you have to unscrew all the rivets after removing the flares... im guessing it was like 8 to 10 for each fender in front.. the back door you have to drill out some brackets, it might be 6 for each door, then the quarter panel might be another 8 holes for each side..

After I did few holes The metal epoxy was great, use sparingly and you have minimal sanding... the first few holes I was using a spackling technique like joining sheet rock.... DONT DO THAT... it took me days to sand back the epoxy... use the technique and use very little and treat each hole like you are filling "nail holes" in the wall and smear it over the hole with the screen.... almost no sanding then..
 
I was lucky that the "gasket" which is a rubber adhesive was dried out(so the fenders were not stuck to the truck" ...if the fenders are not stuck to the truck you are ready to remove....So when the fender is free, you slide or push the fenders forward toward the front of the truck, it should slide right off,. Alternatively, the fenders have tabs, so if you don't care about saving the fenders, you can just rip them off. But be careful not to flex the fenders or body as you pull them off.

The mesh I am referring to is fiberglass tape mesh. and yes about 2 inch squares. I would hold the squares with one finger and smear the epoxy in a downward motion, pushing the epoxy through the screen and through the hole. I hope that helps... I should have taken pictures...
 
Thanks so much for the tips. It sounds doable, although it is snowing here and I can't fit her in the garage I'll have to wait til better weather!
 
If it's not sold, I'm interested. Am in Walnut Creek.
 
Can't PM you for some reason. Am in Bay Area and interested, give me a call: four one five, 260, one seven three eight.
 
I also tried to PM you. Please reach out to me. gaylond @ gmail dot com.
 
You must log in or register to reply here.

Similar threads

L
For Sale Seattle: 1996 FZJ80 triple-locked stock
Replies
2
Views
737
NKP Garage
NKP Garage
nikramos
SOLD 1996 LX450 Supercharged triple locked
Replies
7
Views
953
Fj80oregon
Fj80oregon
jonnyd42
SOLD 1996 LX 450 3x locked 177k miles
Replies
0
Views
662
jonnyd42
jonnyd42
ranchero7
SOLD Salida, CO. 1996 Triple locked Cruiser. 212k miles
Replies
4
Views
1K
ranchero7
ranchero7

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom