1967

1967 FJ40 Land Cruiser. Spring green with three on the tree and vacuum t case system! Runs and starts up great every time, but t case is currently stuck in low. Not sure why it is stuck, but I will be getting into it over my break between semesters at college, any tips would be much appreciated...

Greetings from sunny Arizona. I just had a Toyota factory rollbar shipped to me… Came from Canada… I’m looking at installing it in my 67. Any tips? Obviously, I’ll need to drill holes and probably make a plate for added strength versus just the thin sheet metal.

I'm finally at a point to start this project. Picked up a 67 FJ40 about 4 years ago. Got it for a good price and the seller even delivered it. The pic on Offer Up.

I just picked up this slightly rough 1967 FJ40. There a couple P/O custom holes but most of the open ones seem like they could be factory. Goal is not to do any kind of full restoration but do like to have a "factory look" when possible. 1.) Anybody have photos or manual copies of stock dash...

Hello all — I am looking for an early front heater for my 67 FJ40. Anyone have one sitting on a shelf? Thanks—

=========== NOTE - These are not mine, contact the seller via the Craigslist Ad ================= https://stlouis.craigslist.org/cto/d/wright-city-1967-land-cruiser-fj40/7670340430.html Looking to get rid of our 1967 Toyota Land Cruiser FJ40. The outside is not perfect, but it's in solid...

Hello everyone. I bought a 1967 FJ 40 two years ago as a father/son project for my now 19 year old son, Liam. It had already been a father/son project in the early 1990's when they replaced the original warn out engine with a carbureted 350 Chevy. They also installed a 1976 LC 4spd trans and...

I’m looking for one like this in good working order. I can prob just throw a speedy sleeve on mine but would like to do it right if possible. This a course spline with 8mm bolt holes. Here’s what I’m looking for .

sold

This is not my listin so do not contact me. Thought it seemed like a decent deal for someone else in need of a good project truck.

=========== NOTE - These are not mine, contact the seller via the Craigslist Ad ================= https://portland.craigslist.org/mlt/cto/d/troutdale-toyota-fj40-landcruiser-4x4/7649211031.html Hasn't been driven much in the past couple of years, so time to get rid of it. - 360HP 350 small...

Since 2015 conversion, this FJ40 has received minimal use. I take it out for a drive about once a month and it starts easy every time. Located in northern Colorado, but I can be flexible with delivery as long as it's not during elk season! Asking $32,500. Less than 700 miles since 2015...

I am now the very fortunate caretaker of an AZ 1967 FJ40. Will be lots more in the coming weeks/months. Need to take time and figure out just the small stuff. Some upgrades were done by PO who I am very thank for letting me care for this truck. 1. 4 spd 2. No single barrel, updated two barrel...

Hello, I am looking for a linkage member for my 1967 FJ40. I have the original dash mounted, vacuum-assist 4wd, but the link I have, (shown below) I believe is for a 4-speed and is about 2-3” too long. I am hoping to avoid cutting this down and rewelding it to the correct size, so please let me...

Hi new to the forum. Had my 1967 fj40 for about 20 years or more kept stock besides paint a tires just 31” BFG. Now with looking at lifting it will a new motor, roll cage, doing it more for around town and the trails. So was looking for any one who has done a spring over lift and what problems...

Clutch, brake and accelerator pedal. Linkage included with accelerator pedal. $50.00

1967 FJ40 Blower, Duct, Heater and Controls. Took out of my rig when I put AC in. Fan works, needs to be oiled. Heater core needs to have the nipple re-brazed. Otherwise all good. Have one side defrost duct and fitting. Make me an offer... Located in Houston TX I put in AC so I...

What's my engine? I live in Ecuador and recently bought a 1967 FJ40 hardtop. I couldn't resist it, and after much negotiations I paid $4,500. US. I knew the motor needed work, as well as the body which has a lot of Bondo. My mechanic pulled the motor and we decided to rebuild it top to bottom...

Posting for a one of my best friends brother. Good family that takes care of there stuff. No rust with 90,000 original miles. Located in Utah For details call Dave at (435) 637-1925 This is a landline. Please be respectful. No calls after 9:00 PM or before 8am. $35,000 Here are some pics

Looking for some help with master cylinder replacement on my 67 fj40, it has the very small brake lines and i can not find a size for the fitting that screws into the master cylinder. I want to use an adapter fitting so as to use a master cylinder with 3/16th standard fitting. has anyone done...