Search results for query: *

Forum search Google search

  1. CruiserDave

    Rear locker issue

    I've got a weird rear locker issue going on. The rear locker will not lock in but the actuator is working and the position sensor is new. Today I placed the vehicle on jackstands with all four wheels in the air. Key in the on position (car not running), low range, center diff locked. Turn switch...
  2. CruiserDave

    Wanted  Wanted Ironman radius drop brackets

    Looking for ironman radius arm drop brackets. New or used doesn't matter.
  3. CruiserDave

    Rough Country 16x8 -12 offset

    https://www.roughcountry.com/product/gray-steel-wheelrc516883g?utm_source=google&utm_medium=cpcb&utm_campaign=17867436380|&utm_content=&utm_term=||t||name_first_RC51-6883G-p&gad_source=1&gclid=CjwKCAiAk9itBhASEiwA1my_6xDzhu_TM5PCJqGeBB5eCpU7cyp2lmgayIRpEEL9VqztVjsmHBF8sBoC0F0QAvD_BwE Does...
  4. CruiserDave

    High Lift mount for Dobinsons Rear Bumper

    I made this jeep hinge mount work by drilling two holes in the vertical tire carrier post. I may add another bolt through the foot and use a wing nut to tighten. Right now it is rock solid and doesn't move at all. I know High Lifts aren't as popular anymore but figured I'd share for those...
  5. CruiserDave

    Weird starting problem need help

    Ok the other day I removed the battery and battery tray to adjust my steering box. When I returned everything back to normal and went to start it this problem occurs. Turn key to acc powers up everything hear clicking. Turn key all the way to start it KILLS ALL POWER until I remove negative...
  6. CruiserDave

    Rear heater core plug

    What is everyone using to plug the firewall holes to the rear heater? Getting ready to delete the rear heat and don't want to have open holes there. Thanks in advance.
  7. CruiserDave

    Trans Cooler line help

    OK replaced my radiator, fan clutch, thermostat , etc recently and the other day one of my transmission cooler lines starts to leak. Well come to find out that the fan shroud had caught the line the goes from the cooler to the bottom of the driver's side radiator and pinched it. Now I'm...
  8. CruiserDave

    OME to SLEE 3 degree bushings?

    OK had my OME 2.5" lift (heavy front ,medium rear) installed 2-3 years ago with supplied OME bushings. LX still has twitchy/light steering and I want to fix it. I haven't had the castor read yet but believe it will show being out of spec by the way it drives. So I want to know how I can go about...
  9. CruiserDave

    Help Oil Pan Stripped

    Changing the oil in my daughter's 98 land cruiser and the oil pan drain plug was so tight that it stripped the threads out of the oil pan. What are some options to fix this without getting a new oil pan?
  10. CruiserDave

    New Gen 2 Smittyblit X20 winches

    Does anyone here have any experience with these new winches? http://www.4wheelparts.com/Winches-...aspx?t_c=18&t_s=300&t_pt=100700&t_pn=S/B98512 I'm looking at replacing my Rough Country rs12000s with one since it just took itself out from a sticking solenoid. Broke the line, stretched and...
  11. CruiserDave

    Albright wiring

    Ok my rough country rs12000s winch solenoid just got stuck and turned itself on last Sunday. Broke the line and bent my ironman bumper in. I'm going to fix all this with a kill switch and I want to change to a albright solenoid. My winch has two traditional solenoids, a three pin controller and...
  12. CruiserDave

    Gorges State Park/ Chestnut Mtn Road

    Well went with the wife to Gorges State Park today and hiked up Rainbow Falls Trail to check out all the waterfalls. Very nice place lots of cool waterfalls and swim holes. On the way out we drove up Chestnut Mountain Rd. This road starts out as a gravel two track road that goes up the mountain...
  13. CruiserDave

    Odd temperature problem help

    So I'm having weird ultraguage temp readings on the highway or at highway speeds. Outside temp was around 90 degrees or so and average water temps are high 190's-the highest around 207 with AC on. No hill climbs or heavy loads. As soon as I get to a light or traffic the temp drops to the upper...
  14. CruiserDave

    Hope it's OK if I post this here?

    Hope It's OK if I post this here? If not let me know and I'll delete it. Well got out and drove some of these roads today. Went from Adako to Maple Sally to hwy90/Edgemont to National Forest road (later turns into Roseboro rd) then a right turn onto fs192/Old House Gap road. Then back down...
  15. CruiserDave

    Hurricane Creek Drive

    Well yesterday the wife and I went up and drove hurricane creek, then to max patch, walked the dog up and enjoyed the views. Then down the mountain into Tenn. and back to Asheville and back home. 400 or so miles round trip, good day out. While at Hurricane Creek we are out letting the dog...
  16. CruiserDave

    Ironman bumper owners

    I just received my ironman bullbar and the instructions say to drill the pin holes out. Just wanted to know what they are talking about because the pictures are not very good that come with the instructions. Also how do I hook up the turn signals since it didn't come with anything but bare...
  17. CruiserDave

    Anyone know this road?

    Does anyone know how to find this forest service road? http://www.youtube.com/watch?v=h5sNvbWDmk8 fs192
  18. CruiserDave

    ARB and Engo 10k?

    Just want to know if any of the ARB install kits work with the Engo 10k winch? Or just a homemade spacer set-up?
  19. CruiserDave

    Need new mirrors depo vs kool-vue

    Well my drivers side mirror gave up on me with both tabs breaking AND the little threads for the set screw cracking. So I need a replacement and since they don't come painted I'm going to replace both with black ones. I have seen two aftermarket types available : Depo Kool-vue Depo is about...
  20. CruiserDave

    OME front shock help

    Lift was installed about two weeks ago (heavy front/Med Rear) and a clanging noise was coming from the front end. Pop the hood and both front shocks are loose. Can move them around with my hand( side to side and turn). Send it to a different shop since I needed to have it inspected anyway and...
Back
Top Bottom