NeverFinis's latest activity

I think my set up might be weirder than the rest. All I want to accomplish with this is to get a 12v+ signal out when the high beams are on. This will not power or trigger the actual aux lights. I just need the signal to tell my switch control...

Are you using a 4 pin relay? or a 5 pin relay? It is it normally open or normally closed? I think you should be using a 4 pin relay, normally open. You want the coil GND, Relay pin 86, to be from the high beam GND You want the coil +12V, Relay...

Yeah, your idea would work if I had explained the problem correctly 😂 What is actually happening is that the high beams see 12v+ when the low beams are on and then see ground when the either the high beams are on or when low beams are off (if...

I just did this on my LX450, which is what I think you are trying to do: Builds - LX450 "Rex" Build - https://forum.ih8mud.com/threads/lx450-rex-build.1254004/post-15868347 I have aux bumper lights that can only come on with high beams. There...

Catch can went in

Current status: Things to do: Receive and install conversion harness Receive 1HZ low pressure ac line Then finish installing front clip Receive and install HDJ80 lower radiator hose Receive and install new auto trans and t-case shift boots...

I believe you also want to power the relay with an key on source (ACC/On).

Dragging junk home....

Too much my man! Too much.

OEMs install batteries that way for a few reasons. 1) Reducing the chance of an accidental short during an accident. 2) Reducing the chance of an accident short when using tools near the positive terminal and the body. With that said, I did...

In the picture in question I just made winch hill one on Fordyce trail without winching, body damage or breakage and all you can think of is a rucksack. 🤷‍♂️ their actually called a trasharoo 😉 My 80 is a no frills all business trail rig made to...

I am not going to talk specifically for Cruisers and Co but I have seen a lot of these trucks Dyno'd the problem/mistake some dyno operators have is that they want to pull in a 1:1 gear which would be 3rd gear but you can not lock the auto trans...

You also have the wrong battery. The Land Cruiser uses a 27F battery which has the positive post on the left rear of the battery. The battery you have has the positive on the right side near the fender. As stated in another post in the last...

Not a lot of pictures, but ive been putting miles on the old girl this week. My family flew in from Georgia and their rental car was from the sketchiest looking rental agency ive ever seen. After they tried to double the price of the rental, my...

- oh yeah, I also made a dash mount for our 23Zero solar lanterns. I did the same for my FJC about 4 years ago and it's worked out perfectly. There is no movement when wheeling, and they sit there and recharge until needed. (ignore the...

Based on this discussion, I decided to run 4-gauge welding wire from the battery to the QPM for our camp setup. I'm comfortable with up to 60 amps on that circuit, and I doubt we'll need more than 50, which would be running everything at once...

I have a whole folder from the owner of all the issues. I’ll take some of my own pictures and upload them all here.

this has been brought up before with different rigs https://forum.ih8mud.com/threads/elite-landcruisers.1290840/

I will sometimes assess a vehicle for sale if a potential purchaser asks for opinions here on ih8mud. Only done through pictures provided by the sellers. My experience is spending several years tearing down my own LX450 and mechanically...

Hi everyone, I just want to share my experience with the company Elite Land Cruisers. I’m working on an HJ60 for a buddy of mine who spent over 100k on this complete resto from Elite Land Cruisers, and while from 10 feet she’s a beauty, it’s got...

Found them. Link for anyone else needing clips, retainers, etc:

here are the speakers I used (I mis-stated in a previous post I used Kenwoods in the rear, but I used Alpine all around) Also added the Alpine powered subwoofer in the rear…. which remains a work in progress… I do have an extra set of the...

Time to break out a voltmeter, and the factory ECM....

Good morning. I'm not surprised this thread took off. First and foremost, I thin of myself as an upstanding mud member, and YES, far too trusting with my telephone #. And secondly, I knew right away I got scammed and the likelihood that it...

Alright guys and gals... We finally got the Stage 2 on the dyno last Friday to get the final tune and numbers on @SHELLBACK 's beautiful 80. On the AWD dyno running 14 lbs of boost it made a WHOPPING 364 HP and 481 FT-LBS to the ground!!! If you...