What have you done to your 100 Series this week? (73 Viewers)

[Mauser]

Finally got the Monstaliner sprayed on.

 

[OEMGUY0720]

Those 285/65/18 Falkens? Looks great!

Thanks, those are 275/70R18 falkens.

 

[crolison]

Picked this up with a really really good discount from having so many problems with 4wp and my arb bumper.

 

[crolison]

Also pre wiring the winch controller for in cab controls

 

[CruisingSned]

what color is the fresh?

Bright red.
It’s automatic transmission fluid

 

[FZJ105]

eBay special, as far as I can see it's an ARB snorkel copy. Cost $77 Australian pesos to my door and about 1hr to install

 

[2020 Rocks]

Finally got the Monstaliner sprayed on. View attachment 2734335

My 98 is in need of a paint job, keep leaning towards monsta. Looks great!

 

[TrillyPop]

Installed the 180 degree free standing awning from OVS. Had to make some 1" HDPE spacers to clear the lip on the front runner rack, but otherwise was an easy install with 2 people. Build quality is nice on this thing, especially for the price point. Can't wait to make use of it.

 

[saucebox]

First dirt miles in waaaaay too long with a friend and his just-purchased FJC

 

[Mauser]

My 98 is in need of a paint job, keep leaning towards monsta. Looks great!

Thank you! It is really simple to do. The stuff can be rolled on too, but I wouldn't roll it. Spraying it is so simple, like shooting drywall texture.

 

[bridgeburner]

After spending more than I should have to get pads and rotors for a job that I thought my mechanic would be able to do on Saturday we found out that the truck is to tall to fit into the front door of his garage.
Today I’m reaching out to everyone I know with a large garage to see if they can fit me in for brakes + CV + muffler replacement.
All in all not so bad for a 21yo truck.

 

[crolison]

Mostly installed the winch and cranked the torsion bars for the arb and winch.
Need to get some longer bolts for the winch mounting point so I can use lock washers

 

[WreckDiver1321]

Looking good Chris!

 

[213374U]

Took my girls down to Padre Island National Seashore to do some camping over the weekend

 

[213374U]

Mostly installed the winch and cranked the torsion bars for the arb and winch.
Need to get some longer bolts for the winch mounting point so I can use lock washers

What winch did you go with?

 

[crolison]

What winch did you go with?

It’s a smittybilt xrc9500, nowhere near a top of the line winch but got about 70% off the price.

 

[AK Wes]

After spending more than I should have to get pads and rotors for a job that I thought my mechanic would be able to do on Saturday we found out that the truck is to tall to fit into the front door of his garage.
Today I’m reaching out to everyone I know with a large garage to see if they can fit me in for brakes + CV + muffler replacement.
All in all not so bad for a 21yo truck.

A mechanic that can't fit a Land Cruiser in his garage??? Are you having a Ferrari Dealership do work on your Cruiser?

 

[clrussell]

Busy last couple days.

Yesterday afternoon- finished the paint correction on the passenger side, put the spare under it (turns out a 305/70/16 will fit under there in stock location), started planning the fridge setup.

This evening- replaced front wheel bearings and races, packed with moly grease. Kinda insane how loud the old ones were.

 

[DoughNut]

Just rolled 325,000 miles. At 500,000 she’s getting a 3BT Cummins or a 5.7L swap.

 

[daohaus]

Didn’t like the looks of the factory tundra wheels so I decided to rattle can it. I’m still trying to figure out a good way to use the tundra caps for the front, thinking about using a hole saw and then adapting a plastic tube to clear the dust cap. Any thoughts on how best to do this?