Wrenchin' central

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I can swing by, I dont really have anything new to put on the truck... so we can just keep pulling s*** off of it :)
 
We meeting up this week? Or taking a break?
 
I plan on meeting Mike at his shop on Thursday after work to figure out how to best tweak his recovery points. That's the plan at this moment.
 
I can't make Thursday. Guess it'll be same time, next week.
 
my schedule is up in the air. I am planning on being back Thursday night but probably need to be at home. missed my wedding anniversary (today). Jordon, any chance of swinging by the house on Thursday after work ? Drinks on me.
 
MEMCruiser said:
my schedule is up in the air. I am planning on being back Thursday night but probably need to be at home. missed my wedding anniversary (today). Jordon, any chance of swinging by the house on Thursday after work ? Drinks on me.
Click to expand...

That'll probably work. Please text me an address!
 
I need to build a square front d-shaft, repair/replace a section of broken exhaust pipe and replace my t-case skid plate & trans mount. I don't have my welder up here with me nor do I yet have the square stock for the shaft. I do have a few extra d-shafts that I'm not shy about cutting up though. Anybody already have or have a place to get the square tubing I need to do this? I probably have all the tools needed except the welder. Could all be done at my shop up in Brighton as long as someone can supply a welder.
 
Anybody in town got a plasma cutter? (and know how to use it?)(are they usually 110V or 220?)

How 'bout a 220 welder (and a place to plug it in)?

Mike, does your shop have a 220 outlet?


I want to build a rear bumper, actually have some plans for it, have enough 1/4" plate, but don't really want to cut it out with an angle grinder. I also have access to a 110 welder to tack it together with, but would rather fill it in with a 220.

Jordan, can you get us into the weldin' shop at school? They have a nice mig there. I weldered the mini baja car together with it.
 
don't have 220 in my 2 positions. Don't think there is one anywhere else in bldg but will check. Jordon rolls in this weekend and is moving bride into apt.
 
FJ60Cam said:
Do you have access to the electric panel in your space? (Of course, it doesn't matter if we don't have a welder)
Click to expand...

I do have access to panel. I talked with Landlord, there is 220 single and dual phase that might be pigtailed. I am just quoting him. Do you want to go look at it in morning?
 
I'm back!

Unfortunately, I don't have access to the shop at school. I haven't made a connection in that area.

I have a 220V plasma and welder, but they're in Hot Springs. Not much help, huh?! I've wired 220 into a main panel a couple times now. Just need the 220V breaker. 30 amp for plasma and I think 50 for welder is what I used.

Bomar, what you thinkin?
 
Hey guys, let me know when you plan to do the next wrenching session. I have a PHH to do at some point, and have an oil leak I'd like to get some additional eyes on before planning an attack angle. Also still struggling with the truck's driving manners since putting on the lift, and hope that one of you can point me in the right direction....
 
PHH is outta the way, along with changing/flushing the coolant system and new thermostat. Last of the PM stuff (outside the front rebuid).

Nobody turning a wrench any time soon?
 
You must log in or register to reply here.

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom