Upgrading to a 2650?
Also curious - is there a recommended wheel offset for King 3.0s? I've been considering that setup but I'd like to run 17x8.5 +35s if possible.
What did you do with your Tundra or Sequoia this weekend? (3 Viewers)
- Thread starter Bryanseye
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Also curious - is there a recommended wheel offset for King 3.0s? I've been considering that setup but I'd like to run 17x8.5 +35s if possible.
Rouleur
GOLD Star
Hey bud!
You will probably need to trim at the minimum.
Possibly some chop. +35 is probably optimal.
+18 is dang near perfect IMO.
2650 Harrop.
Rad. No issues rubbing on the remote reservoirs? Most people with King/Fox have 0 offset so I've been having trouble finding info. I'd love to keep the wheels around +18-35 ish.
I don't think I posted here yet. I was about to buy a '24 Tundra when I found this mint '21 with only 8K miles on it. Haven't done anything to it yet, but I'm shopping! ha.
Rouleur
GOLD Star
Good move such a nice unit! You’re going to love her.Rad. No issues rubbing on the remote reservoirs? Most people with King/Fox have 0 offset so I've been having trouble finding info. I'd love to keep the wheels around +18-35 ish.
I don't think I posted here yet. I was about to buy a '24 Tundra when I found this mint '21 with only 8K miles on it. Haven't done anything to it yet, but I'm shopping! ha.
295/70/18 or 285/75/18 I rubbed with 35/12.5017 0s backing wheels locked.
I’ve been thinking about going back to 17s.
Last edited:
Rouleur
GOLD Star
After pulling Evo Corse and Mag and suspension.
That’s a 295/70/18
Classifieds link? I didn’t see the listings when I browsed
Rouleur
GOLD Star
Howdy supercharger is listed on first page. Engine/Transmission
Last edited:
Flower bonanza day for planting season
Broke the donor differentials for my sequoia down, scrubbed them in diesel to clean them up in preparation for locker installation.
Also, measured out shims and got them ordered.
Also, measured out shims and got them ordered.
2024 Sequoia Limited 4x4, non-OR.
Put on FN BFD’s +20mm wrapped in 275/70r18 KO3’s. This is how these buses should be sold.
Put on FN BFD’s +20mm wrapped in 275/70r18 KO3’s. This is how these buses should be sold.
Rouleur
GOLD Star
Excited to strap the Maggie back on with a few other bits and a proper tune.
I don’t hate the “missed leg day” look.
In fact, I actually prefer the look. It’s as the truck should be IMO.
it’s way more fun than driving around with oversized tires with bad handling. I’m sure others would disagree; but I’ve owned a few pros in different configurations, and this is the best, as far as I’m concerned.
Maggie sitting next to H152 kit. Yes complete 152 kit.
I don’t hate the “missed leg day” look.
In fact, I actually prefer the look. It’s as the truck should be IMO.
it’s way more fun than driving around with oversized tires with bad handling. I’m sure others would disagree; but I’ve owned a few pros in different configurations, and this is the best, as far as I’m concerned.
Maggie sitting next to H152 kit. Yes complete 152 kit.
Last edited:
KO3's are out! Crap, I should have waited a little longer to put tires on the 2nd gen.
I've been thinking about doing a very similar build on mine and avoid the headache of chopping for 35s/37s.
H152 kit - I'm very close to pulling the trigger on that myself for my HDJ81. Are you keeping it/going to use it? Or are you selling it?
Rouleur
GOLD Star
On the fence may be picking up a POV from a good buddy.
I guess you knew I had a FTE80?
Last edited:
I’m actually really impressed with the on road characteristics. They’re barely louder than the stock tires and the ride isn’t any worse. I had Nitto Terra Grapplers on my 4Runner and they were extremely loud and harsh. These are E load and I’m running them at 42 psi cold based on the P-E load graphs I’ve seen.
That's good to hear! Have you had KO2's before? I'm curious about the rain and snow performance of these compare to the KO2's.
I just had to get a set KO'2 due to an unfortunate encounter with a couple of nails and bolts.
Starting my E-Locker install on the 2nd gen Sequoia. Using the press to hold the carrier while I torque the ring gear bolts.
These probably won’t see snow unless we make a trip to Snowshoe WV. I’ll be taking them on the beach this week though.
Road Trip...
Family in Alberta and then for some time in Jasper and Banff National Parks.
Video of Mt Robson.
Family in Alberta and then for some time in Jasper and Banff National Parks.
Video of Mt Robson.
yngmrostrvile
GOLD Star
Not my 01 Sequoia but new to my younger brother....Did tbelt and water pump, lower ball joints, cleaned up all four wheel brakes with a rear pad slap, replaced front struts, and fluid eclxchange on trans PS transfer and front and rear diffs. All aided by Sierra Nevada Big Little IPA
