What are you working on? (4 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I used Dupli color wheel paint from Advance. Graphite. Base and clear. This was for the bumper wing.

IMG_0836.jpeg


IMG_0835.jpeg


IMG_0834.jpeg


IMG_0833.jpeg
 
Last edited:
Finally got some time to work on the 80. Got the bumper lights installed and the winch mostly installed minus finishing some wiring

IMG_9593.jpeg
 
Finally got the White Knuckle sliders on. The skid for the t-case will have to wait till I put the gears in. They look great, and with the top plate, no risk of slipping into the whole and breaking anything.

I will tell you, they took about a week to install. Body work, paint, new door speakers, weatherstrips, mouldings, drivers door handle, all to get them on! Oh and Betsy to install nuts and bolts while I held them in place.😊

IMG_0841.jpeg


IMG_0840.jpeg


IMG_0839.jpeg


IMG_0838.jpeg


IMG_0837.jpeg
 
HOT day finishing up the Tacoma but it's fully done and my brother just left with it 15 minutes ago. Autumn enjoyed the pool and Lauren helped me give it a bath. All my measurements lined up and I tested 4wd, low range, and the locker for fun in the ditch. Thank you so much to you guys for the advice along the way, especially to @Toyodajunkie for the welding help and @Land Shark for letting me borrow some good tools throughout the whole project. @matzell I'll point him to you when the leaf spring breaks off on his way home.

IMG_9355.jpeg


IMG_1524.jpeg
 
matzell said:
Finally got the White Knuckle sliders on. The skid for the t-case will have to wait till I put the gears in. They look great, and with the top plate, no risk of slipping into the whole and breaking anything.

I will tell you, they took about a week to install. Body work, paint, new door speakers, weatherstrips, mouldings, drivers door handle, all to get them on! Oh and Betsy to install nuts and bolts while I held them in place.😊

View attachment 3666783

View attachment 3666784

View attachment 3666785

View attachment 3666786

View attachment 3666787
Click to expand...
Dang that's looking real nice
 
FamilyCamper said:
HOT day finishing up the Tacoma but it's fully done and my brother just left with it 15 minutes ago. Autumn enjoyed the pool and Lauren helped me give it a bath. All my measurements lined up and I tested 4wd, low range, and the locker for fun in the ditch. Thank you so much to you guys for the advice along the way, especially to @Toyodajunkie for the welding help and @Land Shark for letting me borrow some good tools throughout the whole project. @matzell I'll point him to you when the leaf spring breaks off on his way home.

View attachment 3666978

View attachment 3666979
Click to expand...

Very impressive! This was a huge project and you knocked that out in no time
 
In an attempt to make Lynchburg Lemonade look a little better for its trip out to SAS 8. I decided to clean up the body from where I laid it over last year out there. I worked the metal first and then skimmed with body filler.

I need to lay some paint down, but it should look a bit better from 20 feet!😁
I also have Betsy sewing a steering wheel cover on.

IMG_0897.jpeg


IMG_0896.jpeg


IMG_0894.jpeg


IMG_0893.jpeg
 
matzell said:
In an attempt to make Lynchburg Lemonade look a little better for its trip out to SAS 8. I decided to clean up the body from where I laid it over last year out there. I worked the metal first and then skimmed with body filler.

I need to lay some paint down, but it should look a bit better from 20 feet!😁
I also have Betsy sewing a steering wheel cover on.

View attachment 3677518

View attachment 3677519

View attachment 3677520

View attachment 3677521
Click to expand...
Oh no while its still in the truck. Bet she had fun with that
 
Picked up a new project thanks to Rob, jumped right in and picked up a new (150k) motor for it and started on some small stuff. Cleaned outside, disassembled engine bay to prepare to pull, and today @Land Shark accompanied me to scavenge a radiator shroud and intake assembly from a parts truck west of Richmond. Ended up with a steal on the parts and a very nice driver seat. This project would not be happening without the community and I wouldn't have the confidence to do it without this club and the support I know I have so thank you to all I really appreciate all of it.

IMG_1648.jpeg


IMG_1649.jpeg


IMG_1566.jpeg
 
You must log in or register to reply here.

Users who are viewing this thread

Total: 5 (members: 1, guests: 4)

Share this page

Back
Top Bottom