SOLD Sears Selectro Dualmatic Course Spline Hubs - San Diego (1 Viewer)

bmoonhajjar

GOLD Star
Joined
Oct 22, 2019
Messages
2,004
Location
San Diego
Refurbished these Sears Course Spline Hubs in a FJ40 Pewter Color. Thoroughly greased up using AeroShell Grease 33. Ready to install.
$250
IMG_5166.jpg
IMG_5165.jpg
IMG_5163.jpg
 
Last edited:

bmoonhajjar

GOLD Star
Joined
Oct 22, 2019
Messages
2,004
Location
San Diego
Check to see if they will fit and we can make a deal. Not looking to get rich. I bought them for $100 and threw some rebuild parts and elbow grease into them. Cash-wise I am only into them for around $150, so if they will work, I would go $175 + shipping if that helps. I am waiting on new rubber seals since the ones pictured are too loose in my opinion. Other than that, they should be good to go.
 
Joined
Aug 9, 2015
Messages
113
Location
Lebanon, IN
Check to see if they will fit and we can make a deal. Not looking to get rich. I bought them for $100 and threw some rebuild parts and elbow grease into them. Cash-wise I am only into them for around $150, so if they will work, I would go $175 + shipping if that helps. I am waiting on new rubber seals since the ones pictured are too loose in my opinion. Other than that, they should be good to go.
I removed mine. They are Selectro and have that name on the knob part of the lockers. They are 6 spline off of a ‘67 fj45 LPB. One side looks just like yours, with 6 screws holding the knob in place. However the other one only has 3 screws and screw holes to hold the knob on. Did yours come off of a cruiser?
 

MexicanNewby

SILVER Star
Joined
Apr 3, 2018
Messages
299
Location
Mexico City
Check to see if they will fit and we can make a deal. Not looking to get rich. I bought them for $100 and threw some rebuild parts and elbow grease into them. Cash-wise I am only into them for around $150, so if they will work, I would go $175 + shipping if that helps. I am waiting on new rubber seals since the ones pictured are too loose in my opinion. Other than that, they should be good to go.

Hey, where do you but the rubbers for maintenance? I have a pair of Selectros and would like to give them some maintenance.

Beautifulset and by the way

J
 

Drake2

SILVER Star
Joined
Oct 11, 2017
Messages
2,513
Location
Wisconsin
I removed mine. They are Selectro and have that name on the knob part of the lockers. They are 6 spline off of a ‘67 fj45 LPB. One side looks just like yours, with 6 screws holding the knob in place. However the other one only has 3 screws and screw holes to hold the knob on. Did yours come off of a cruiser?
Can you upload a picture/s?
 

bmoonhajjar

GOLD Star
Joined
Oct 22, 2019
Messages
2,004
Location
San Diego
I removed mine. They are Selectro and have that name on the knob part of the lockers. They are 6 spline off of a ‘67 fj45 LPB. One side looks just like yours, with 6 screws holding the knob in place. However the other one only has 3 screws and screw holes to hold the knob on. Did yours come off of a cruiser?
These were pulled off of a 68 FJ40 when I got them. Couldn’t tell you much else about them except several other companies made very similar ones like Selectro, Dualmatic, Power Train. I have also see a Dana once that looked like this but had 8 bolt holes.
 
Joined
Aug 9, 2015
Messages
113
Location
Lebanon, IN
These were pulled off of a 68 FJ40 when I got them. Couldn’t tell you much else about them except several other companies made very similar ones like Selectro, Dualmatic, Power Train. I have also see a Dana once that looked like this but had 8 bolt holes.
I read that Selectro made them for Sears. I’m assuming my truck has 2 different hubs on it. Like a 1st & 2nd design, or someone swapped knobs.
 

Users who are viewing this thread

Top Bottom