GX460 & GXOR B.S. thread (28 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I've been running a cowl intake on my 460 for a few years now. I don't have any pics but it was super simple. 4"to3" elbow off the intake box. Straight 3" intake pipe, I didn't need to make any bends or use flexible tubing. Cut a 3" hole to the cowl, bolt on a 3" flange and another 3" elbow.
 
I've seen a few on FB GXOR where they run a flexible hose from the intake hole in the inner fender up along the inside of the fender back into the cowl area. Hard to find a lot of pictures about it.

View attachment 3728874

View attachment 3728875
So that is where my RV septic dump tube went! There I was thinking a Civic owner stole it! 🤣
 
I've been running a cowl intake on my 460 for a few years now. I don't have any pics but it was super simple. 4"to3" elbow off the intake box. Straight 3" intake pipe, I didn't need to make any bends or use flexible tubing. Cut a 3" hole to the cowl, bolt on a 3" flange and another 3" elbow.
Hey @OCGX would you mind spanning a couple pictures? I'd love to see the exact location of your cuts and I'm sure others on here would as well. Thanks!
 
Hey @OCGX would you mind spanning a couple pictures? I'd love to see the exact location of your cuts and I'm sure others on here would as well. Thanks!
LGF_tacoma on IG has a reel that shows the hard parts. Where to cut the inner fender, and bolt up the flange. The GX is almost exactly the same.



I’ll try to snap some pics too.
 
LGF_tacoma on IG has a reel that shows the hard parts. Where to cut the inner fender, and bolt up the flange. The GX is almost exactly the same.



I’ll try to snap some pics too.

Pictures would be appreciated.

What is that piece of metal he attaches after cutting the hole? Like a support for the piping?
 
I've been running a cowl intake on my 460 for a few years now. I don't have any pics but it was super simple. 4"to3" elbow off the intake box. Straight 3" intake pipe, I didn't need to make any bends or use flexible tubing. Cut a 3" hole to the cowl, bolt on a 3" flange and another 3" elbow.
Most importantly, did you see/feel any performance increases, e.g.: MPG, seat of the pants acceleration, or?
LGF_tacoma on IG has a reel that shows the hard parts. Where to cut the inner fender, and bolt up the flange. The GX is almost exactly the same.



I’ll try to snap some pics too.

Assuming air intake is now from the air vents below the windshield wipers?
 
A GX550 pulled up next to me on my commute this morning. We both gave each other the peace sign. Life is good.
 
We saw quite a few GX550's between Texas and Florida over the past week, maybe twice as many of the 250 Series LC as well. The misses is obsessed with the Overtrail and she's looking forward to getting her own next year.
 
We saw quite a few GX550's between Texas and Florida over the past week, maybe twice as many of the 250 Series LC as well. The misses is obsessed with the Overtrail and she's looking forward to getting her own next year.
Same. I've been seeing tons of 550s in the Prosper area, far north of Dallas.
 
A GX550 pulled up next to me on my commute this morning. We both gave each other the peace sign. Life is good.
And I thought only the girls in Japan threw up "peace signs" in all their still photos!
I guess it's a west coast thing, but we usually do a "shaka" 🤙 (it's actually a Hawaiian thing, meaning "hang loose")

1726938499823.jpeg
 
Last edited:
I have done it forever, a lot of the folks my age in the Midwest do.
 
  • Like
Reactions: r2m
I guess it's a west coast thing, but we usually do a "shaka" 🤙 (it's actually a Hawaiian thing, meaning "hand loose")
I lived in California for 6 years until '21, and apparently I subconsciously picked that up while out there.

Now that I'm back home in the midwest I still find myself doing that all the time to people in lieu of a wave or thumbs up. I had no idea it was called a shaka though.
 
And I thought only the girls in Japan threw up "peace signs" in all their still photos!
I guess it's a west coast thing, but we usually do a "shaka" 🤙 (it's actually a Hawaiian thing, meaning "hand loose")

View attachment 3731363

It is "hang loose" or in the 70's was more "hang ten" on the Rock (Oahu) with the coastal surfing crowd, and once in a while seen it in SoCal but not often. I spent 6 months on the Rock TAD in the mid 70's during the 5 years that I was homeported in San Diego. And of course have to stop there for a bit on the way to a Western Pacific deployment.

Just got back from the Sunset Country of Ontario with the Admiral, the Skipper couldn't make it this year he is closing on his house in Boston and downsizing. His other home is in Oahu easy to figure out which home he spends 6 months at. He purchased his Oahu house in the early 80's. The 3 of us have been stationed in Pearl Harbor at one time or another and when calling each other will often greet and close our phone conversations with Aloha. None of us will give each other the shaka though, that is for the young surfer crowd. More times than not back then it meant hang loose, usually along the lines of Eh brah lets go smoke some Pakalolo. Had no idea that it is now called the shaka.

Never dreamed that I'd end up in the Upper Midwest. The one thing that is consistent across the nation in rural areas is the one finger salute in acknowledgement or respect. Subtle and that is more my style and what I do, like this

CC-194-076-800.jpg


I picked that picture because I had a 67 Mustang with a 289 and it was burnt orange as well. It was my last car before I got my first 4x4 a 77 FJ55 Iron Pig Land Cruiser and haven't owned a car since, only 4x4's. Been more than a few years.
 
It is "hang loose" or in the 70's was more "hang ten" on the Rock (Oahu) with the coastal surfing crowd, and once in a while seen it in SoCal but not often. I spent 6 months on the Rock TAD in the mid 70's during the 5 years that I was homeported in San Diego. And of course have to stop there for a bit on the way to a Western Pacific deployment.

Just got back from the Sunset Country of Ontario with the Admiral, the Skipper couldn't make it this year he is closing on his house in Boston and downsizing. His other home is in Oahu easy to figure out which home he spends 6 months at. He purchased his Oahu house in the early 80's. The 3 of us have been stationed in Pearl Harbor at one time or another and when calling each other will often greet and close our phone conversations with Aloha. None of us will give each other the shaka though, that is for the young surfer crowd. More times than not back then it meant hang loose, usually along the lines of Eh brah lets go smoke some Pakalolo. Had no idea that it is now called the shaka.

Never dreamed that I'd end up in the Upper Midwest. The one thing that is consistent across the nation in rural areas is the one finger salute in acknowledgement or respect. Subtle and that is more my style and what I do, like this

CC-194-076-800.jpg


I picked that picture because I had a 67 Mustang with a 289 and it was burnt orange as well. It was my last car before I got my first 4x4 a 77 FJ55 Iron Pig Land Cruiser and haven't owned a car since, only 4x4's. Been more than a few years.

I haven't owned a car in over a decade either. The only car I still desire is of the sports car ilk but when I start to think about it I always talk myself out of getting serious about one because I simply won't use it enough. $100K+ for a fair weather vehicle that might see the light of day 1-2 times per month at best, the juice just doesn't seem worth the squeeze.
 
It is "hang loose" or in the 70's was more "hang ten" on the Rock (Oahu) with the coastal surfing crowd, and once in a while seen it in SoCal but not often. I spent 6 months on the Rock TAD in the mid 70's during the 5 years that I was homeported in San Diego. And of course have to stop there for a bit on the way to a Western Pacific deployment.

Just got back from the Sunset Country of Ontario with the Admiral, the Skipper couldn't make it this year he is closing on his house in Boston and downsizing. His other home is in Oahu easy to figure out which home he spends 6 months at. He purchased his Oahu house in the early 80's. The 3 of us have been stationed in Pearl Harbor at one time or another and when calling each other will often greet and close our phone conversations with Aloha. None of us will give each other the shaka though, that is for the young surfer crowd. More times than not back then it meant hang loose, usually along the lines of Eh brah lets go smoke some Pakalolo. Had no idea that it is now called the shaka.

Never dreamed that I'd end up in the Upper Midwest. The one thing that is consistent across the nation in rural areas is the one finger salute in acknowledgement or respect. Subtle and that is more my style and what I do, like this

CC-194-076-800.jpg


I picked that picture because I had a 67 Mustang with a 289 and it was burnt orange as well. It was my last car before I got my first 4x4 a 77 FJ55 Iron Pig Land Cruiser and haven't owned a car since, only 4x4's. Been more than a few years.
My bad, sloppy typing. Yes I know it's han"g" loose, not han"d" loose.
Thanks for catching that! I imagine for those unaware, "hand loose" could actually be correct, and NOT a typo.
(what a rookie move...)
 
CC-194-076-800.jpg


I picked that picture because I had a 67 Mustang with a 289 and it was burnt orange as well. It was my last car before I got my first 4x4 a 77 FJ55 Iron Pig Land Cruiser and haven't owned a car since, only 4x4's. Been more than a few years.
I get that a lot hitting B roads.
 
Bug impacts have always been a PITA for me cleaning my rigs over the years. 1K round trip plus ~500+ miles off road over the last week I had more than my fair share of bugs smack the front end, grill and mirrors. Well mirrors on the highway on the trails they were always folded in.

With the above average temps the mosquitoes would eat you alive without deet. And buggins for the gnats. Plus who knows what else that flies. In the past I've tried various bug and tar remover and all different types of washes but nothing really stuck out as better than anything else.

Today unpacking I remembered that I had a bottle of Chemical Guys bug remover that I got this summer but never opened. Had never used any of their stuff before and figured it was time to try it.

54014820475_1a7475f4b5_b.jpg


Let the Chemical Guys bug remover mixed with water sit for a minute and then scrubbed with my standard car brush. Not hard or long no longer than normal cleaning. Count me a fan at least of the bug remover.

54014820480_3cd3897aea_b.jpg


The front end had some black spots on it in places so did it twice. On closer inspection the black is because I left some paint behind in Canada. Some trails were pretty overgrown on all sides and top so were more a tunnel of trees. And of course tight K turns to turn around require a bumper bump up against trees.
 
Bug impacts have always been a PITA for me cleaning my rigs over the years. 1K round trip plus ~500+ miles off road over the last week I had more than my fair share of bugs smack the front end, grill and mirrors. Well mirrors on the highway on the trails they were always folded in.

With the above average temps the mosquitoes would eat you alive without deet. And buggins for the gnats. Plus who knows what else that flies. In the past I've tried various bug and tar remover and all different types of washes but nothing really stuck out as better than anything else.

Today unpacking I remembered that I had a bottle of Chemical Guys bug remover that I got this summer but never opened. Had never used any of their stuff before and figured it was time to try it.

54014820475_1a7475f4b5_b.jpg


Let the Chemical Guys bug remover mixed with water sit for a minute and then scrubbed with my standard car brush. Not hard or long no longer than normal cleaning. Count me a fan at least of the bug remover.

54014820480_3cd3897aea_b.jpg


The front end had some black spots on it in places so did it twice. On closer inspection the black is because I left some paint behind in Canada. Some trails were pretty overgrown on all sides and top so were more a tunnel of trees. And of course tight K turns to turn around require a bumper bump up against trees.
The photos of your mirrors reminded me that it seems my mirrors get hit a lot more than the leading edge of my hood, especially off roading with debris being kicked up on trails by the front tires.
Too bad there isn't a clear cover for mirrors that you can just take off and throw in the dishwasher to clean them!
 
My mirrors and the leading edge of the hood are always the most beat up on my vehicles. We live on the Texas coast so bugs are insane 7-8 months out of the year.
 

Users who are viewing this thread

Back
Top Bottom