Jeremiah @proffittscruisers.com has one for me...
thanks,
manny 72fj40
thanks,
manny 72fj40
Wanted FJ60 Manual (31 Viewers)
- Thread starter Webster
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I have a set of TPI 2.5" springs. No sag and ride very well. They are about 4 ish years old, I'd like to trade because I"m ready to go up to 4" of lift.
Jody.
Jody.
tucker74
Moderator
FJ55 Fan Shroud?
Anyone have a fan shroud for an FJ55 they don't need? Any year '68-'79 will work w/o factory AC...as long as it's serviceable.
Always looking out for good vent window rubber as well
Tucker
Anyone have a fan shroud for an FJ55 they don't need? Any year '68-'79 will work w/o factory AC...as long as it's serviceable.
Always looking out for good vent window rubber as well
Tucker
I have a housing, no guts though... no third either.... PM w/ offers...
ahhh, wrong corner
Looking for FJ80 front axle...
Like the title says. Locker not important, but I wouldn't turn down a E-locked one!
Let me know what you have: jason@fawkit.org
~Jason
Like the title says. Locker not important, but I wouldn't turn down a E-locked one!
Let me know what you have: jason@fawkit.org
~Jason
62 Lift Kit and visors
Looking for a used lift kit for a FJ-62 and sunvisors out of a 62 also if anyone has either let me know!!
Thanks
Burl
Looking for a used lift kit for a FJ-62 and sunvisors out of a 62 also if anyone has either let me know!!
Thanks
Burl
I have a set of springs that will give you the ability to run 33's without contact.
Springs are heavy I'm in AZ so shipping could be pricey. where are you located?
Phil
Springs are heavy I'm in AZ so shipping could be pricey. where are you located?
Phil
Rear Sway bar from FJ62
If you have one that you will part with, please PM me.
Thanks,
Mike S
If you have one that you will part with, please PM me.
Thanks,
Mike S
transfercase internal part
http://www.sor.com/sor/cat070.tam?xax=16071&page.ctx=cat070.tam
need number 23 on one piece case, 75 model, all my spares show alot of wear also.
And F*** sor on this, they jerked me around, didnt send out my parts still 2 weeks after i ordered them, still were trying to charge me for a previous purchase made 2 yrs earlier which was long paid for. Cancelled my order and held up a few fingers to them. I put it together with what i had and now its bothering me with its noisy slop.
http://www.sor.com/sor/cat070.tam?xax=16071&page.ctx=cat070.tam
need number 23 on one piece case, 75 model, all my spares show alot of wear also.
And F*** sor on this, they jerked me around, didnt send out my parts still 2 weeks after i ordered them, still were trying to charge me for a previous purchase made 2 yrs earlier which was long paid for. Cancelled my order and held up a few fingers to them. I put it together with what i had and now its bothering me with its noisy slop.
Eric, you are the man! That place is only 10 mins away! About halfway between Riverside and San Bernardino, CA. Called and they had what I wanted in stock ready for pickup at $70 a pair. Definitely the cheapest I've encountered.
Mike R.
Mike R.
e rock said:
OME medium load springs for '93 LC
I need used front and rear springs. Somebody please hook me up. Thanks.
I need used front and rear springs. Somebody please hook me up. Thanks.
'93 LC front bumper end cap
Well, I guess it's called the end cap. I need one for the driver's side so I don't have to buy the whole bumper. Thanks.
Well, I guess it's called the end cap. I need one for the driver's side so I don't have to buy the whole bumper. Thanks.
Toy mini wanted in Utah
Looking for a Toy mini P/U. Goal: Formula Toy project. Have no intention of competing, just want to beat on it and save some abuse to my FJ. Doesn't have to be running condition or even have an engine if remainder is intact. Will consider a rolling chasis. Even an IFS.
Looking for a Toy mini P/U. Goal: Formula Toy project. Have no intention of competing, just want to beat on it and save some abuse to my FJ. Doesn't have to be running condition or even have an engine if remainder is intact. Will consider a rolling chasis. Even an IFS.
good excuse to buy another fj40,
seriously though i build minis for buddies, and the fj40 cruiser is just a much
better platform to work with.
currently mild to wild minis, stock soa with locks on 40s, to sbc doubler 1 tons on 43"s,
looked at doing a set of rockwells under one as we have them, but just not good enough
chassis IMO.
BTW my buddy is selling a
1990 black toy extended cab, 280k miles on truck, 130k on new V6, new clutch and trans, 4-5 in superlift springs, 3 in body lift, 5.29s and lockrights both front and rear 5,000 miles on these, 80+% 37x12.50x15 SSRs on 15x10 eagle 589s, Air works. $ 5500 make offer as it needs to go.
new headgaskets as of like 15,000 miles ago.
A daily driver i could see. Something different i guess it would work, but it would take
$$$ and time away from the cruiser! lol
seriously though i build minis for buddies, and the fj40 cruiser is just a much
better platform to work with.
currently mild to wild minis, stock soa with locks on 40s, to sbc doubler 1 tons on 43"s,
looked at doing a set of rockwells under one as we have them, but just not good enough
chassis IMO.
BTW my buddy is selling a
1990 black toy extended cab, 280k miles on truck, 130k on new V6, new clutch and trans, 4-5 in superlift springs, 3 in body lift, 5.29s and lockrights both front and rear 5,000 miles on these, 80+% 37x12.50x15 SSRs on 15x10 eagle 589s, Air works. $ 5500 make offer as it needs to go.
new headgaskets as of like 15,000 miles ago.
A daily driver i could see. Something different i guess it would work, but it would take
$$$ and time away from the cruiser! lol
