F Intake, Carb, Header $300 Shipped Conus

[Delancy]

Location

United States

Or best offer....any offer will be considered, honestly, since I don't know the value of any.

Figured carb was a $100 core with Jim C.

I paid $200 for a mated intake/exhaust manifold, so thought the header and intake should be similarly priced.

(But did just give a intake/exhaust manifold to Cruiser Corps)

I'm not here to profit, but attempting to recoup some of the expenses I've incurred, be them reasonable or getting screwed by my own ignorance.

Anyhow, here it is. Lets get it gone!






































There's really not much point in asking me questions because, quite frankly, I can't answer.

Have this F.5 and an F disassembled that I need to liquidate due to the changed fate of this Pig and the short amount of time I've to get the good off of her.

 

[PabloCruise]

Chris, let people know what year the carb is from.

'71?

 

[Delancy]

Chris, let people know what year the carb is from.

'71?

PC,
I wish I could say with certainty, but can only report what the seller told me.

The 71 F and intake/header were swapped for a 73 F.5, but he used the carb from the F.

I had the 71 mated manifolds I have to Cruiser corps to partially validate.

It's a core carb, and Poser advised a $20-40 value. Add the insulator and studs at $25 and it's worth a lot less than listed.

In other words, I don't know.

 

[nuclearlemon]

PC,
I wish I could say with certainty, but can only report what the seller told me.

The 71 F and intake/header were swapped for a 73 F.5, but he used the carb from the F.

there is a letter and number code stamped in the carb. could you post that? it appears to be a cable setup. if so, i'm interested at the more appropriate prices, since the carb cable for my 45 is now going on bosshogs rig

 

[Delancy]

Give me an a couple hours, Ige.

Can you use the intake, too?

I'm a little concerned about separating the carb from the manifold for fear of cracking insulator, unless you say it's a non-issue or of no value.

 

[nuclearlemon]

Give me an a couple hours, Ige.

Can you use the intake, too?

I'm a little concerned about separating the carb from the manifold for fear of cracking insulator, unless you say it's a non-issue or of no value.

we've got plenty of intakes, so not needed. chances of cracking the intake aren't that huge and we've got those here too.

 

[Delancy]

If there's anything not pictured that'd be a typical inclusion, please advise.

Did the pic of casting show?

If not, appears to be 1 C 19

 

[Delancy]

Here's a landscape pictorial of a few other components.....





















Disassembled is an F.

No clue what the springs are from, but not a Pig, best I can tell.





I'm not going to have time to pull the current engine, so guessing I'll put the hood back on to keep the elements out of the engine bay.

Want this all gone, folks, save the shell of the 71.

Have a whole host of other parts that need to go, too, and inevitably, a titled rolling chassis.

 

[Pighead]

If not, appears to be 1 C 19

March 19, 1971

(want)

 

[Delancy]

March 19, 1971

Work for y'all?

 

[Pighead]

Well, I hope to make it work...

 

[nuclearlemon]

If there's anything not pictured that'd be a typical inclusion, please advise.

Did the pic of casting show?

If not, appears to be 1 C 19

gone to pm.

 

[Delancy]

gone to pm.

Replied.

Carb's going to Ige.

Rest is still available.

Lets get it gone!!!!!!

 

[Delancy]

Intake is off and ready to go. $100 shipped, OBO.

Header is off and ready to go. $100 shipped, OBO.

 

[Delancy]

B T T T.

 

[Delancy]

Taking offers.

 

[justchillinout]

Hey I notice some shackles in a previous pic. Any info on them? Interest in selling? Interested in putting in a box the would make it to the Great White North?

Thanks.

 

[Delancy]

Hey I notice some shackles in a previous pic. Any info on them? Interest in selling? Interested in putting in a box the would make it to the Great White North?

Thanks.

First, let me confirm that I have all 4 tomorrow.

No info on, but will measure and post tomorrow.

Yes, I'm interested in selling and yes I can put in a box and ship to the GWN.....even though I'm uncertain where the GWN is.

Edited: For that matter, most everything in the pics are for sale, including a disassembled F, assembled and (barely) running (if sputtering while pouring fuel down the carb counts) F.5.

 

[Delancy]

Can only find three shackles, so far.

 

[Delancy]

Going to post a new thread in general parts for the remaining header and intake.