engine

Looks like someone stuck a pencil through the check engine lens on my dashboard. Its badly cracked. Looking for a replacement please.

So I did a cat back exaust , I kept 1 magnaflow cat ,flowmaster 50 mufler 2 1/2 pipe split into 2 at the axle. It seems like the engine temp has droped about 5 degrees when I check my tourqe pro .can anyone confurm this?

Hi All, I have a 1997 4.5L land cruiser engine for sale. It has not been stored outside but in my shop on an engine stand. This engine is located in Fort Collins, CO. Asking $350. Please call Steve at 970-614-8302 or email at stv_007@yahoo.com.

*should read NEW nosels needed* Hey guys I've been comparing my cruiser engine sound to all my friends, mine definitely sounds rougher, a bit more agricultural, and rattly... Not smooth like some of my friends I took it to a local mech, he said the nosels are probably done in I've had new...

So I'm new to all this, I just replaced my radiator and thermostat today, I went to "burp" the air out, took the radiator cap off and heat defrost full blast, Ran the truck for about 30 min, never saw any bubbling coming out of the radiator at all, but thermostat gauge started going up and up...

Hey Folks! Just put in a rebuilt 1FZ and overhauled the tranny. All is together and running smoothly, however there is a slight drop in RPM's when I let of the gas at 2k RPM or above (under load) and the check engine light flashes. It has stalled from this twice. I'm thinking the belts could be...

Does anyone know the part number for the engine speed sensor inside of the fuel injection pump and where to get one. Thanks

and.. she's alive! What an experience, long but rewarding! First start vid:

Anyone used torque plates on bore or hone jobs for their engine? Did you use aluminum or steel plate and what are your thoughts? Did you take multiple before and after bore measurements, and if so, how did it turn out? I am doing a diagnostic teardown and blueprint job. 1FZ engine building and...

I live in Myanmar and drive a 1980 BJ44. Some of the places I go are quite challenging with real bad or no roads, driving on shallow river beds and pretty steep climbs. I sometimes feel that I could do with more engine power. My car is a 1980 BJ44 with original 1B diesel engine. I have upgraded...

Hi, I am new here and have a question. I picked up a 1974 FJ40 last summer and it came with a hole rusted out 1977 for parts. The engine was not in it but I have it. Now my 1974 should have a F code engine and it has a 3 speed tranny, I would think the other engine would be a 2F engine but the...

hi sir I have hilux revo 2017 2.7 litre 4 cylinder automatic transmission 6 speed I wont to replace the engine from 4 cylinder 2.7 to 6 cylinder 4.0 where can find complete engine wiring harness for v6 hilux original can fit direct to my hilux 2016 without modified To improve a car's...

No, not a second battery - and not just moving the primary to the typical secondary spot - but actually located the primary battery somewhere else in the engine bay? Just wondering what people came up with. My tire looks like it might get into that area when stuffed and turned

I'm trying to resolve a myriad of braking problems with my '86 which has been holding me back from driving it more. One item I can't figure out, is that when I pump the brakes at idle, the engine RPM's drop to ~400, nearly stalling the engine. Any ideas what might be going on?

Hey all - Finishing up fixing my V8 conversion (Gen 1 283 SBC) that my PO had butchered. I stick mostly to the @Downey conversion manual, but I've run into an (anticipated) issue clearing my power steering pump. Common wisdom says to mount the engine 1-1.5" toward the driver's side to allow...

A lot of guys remove the engine cover, why? I dont see a lot of reason either way just thought I would see what guys have to say.

I have a higher mileage good runner. Exact mileage is unknown though. No leaks. Came from a 94. $800 palleted/strapped.

We are looking at installing a Ford 302 from an older Ford Bronco into a 1980 FJ40 that has no engine. Question is there a model 302 engine we should be looking for? We have a 1973 302 motor that is being rebuilt. Also what is a good adapter for a 302 to a 4 speed stock FJ40? Thanks

Evening all! I am in need of a functional temp gauge for a 73 F engine. The rest of my gauge cluster works, but the temp gauge does not work. Thank you in advance! Dave

Hi. We're looking for a replacement 1FZ-FE engine for our '97 FZJ80. Preferably rebuilt or low mileage, but beggars can't be choosers I guess. My boyfriend blew up the engine, so we need to replace it ASAP. (He said he was sorry.) It actually just seems to be a severe rod-knock. We're around...