engine

I have a 1967 fj40 rolling chassis with numbers matching engine. I also can sell tub. please contact me at 714 349 6798 or matt@pacific1lending.com. I have title in hand. location is Huntington beach ca 92648 2

I have a 1967 fj40 rolling chassis with numbers matching engine. I also can sell tub. please contact me at 714 349 6798 or matt@pacific1lending.com. I have title in hand. location is Huntington beach ca 92648

I've been working on a replacement for my 80's primary engine earth cable linking the neg terminal of the main battery direct to the connection point at the bottom of the 1hz engine block. This is what the end fixed to engine looked like until I took it off yesterday: '] pic page The bolt is...

Strong oil pressure, no knocks or noises, runs very good, and runs cool. I welcome you to test this engine out, still in the car before we pull the engine. I will sell it as complete as you want it, $750 to $950 with starter, alternator, and everything including MAF and smog parts. Video of...

I just pull my engine. Putting in a lq9. I am looking to sell the engine and transmission. I really prefer to sell it as a whole engine/transmission or at least as major pieces. I don’t really know prices but a lot of what I put in is new oem genuine Toyota parts. Please pm me and we can talk...

Just picked up a 91 land cruiser for my wife this weekend. It had 199,xxx miles. Super clean, inside and out, paid $5,000. The seller was super honest and super cool, probably the best Craigslist in my whole life. He mentioned that there's a little oil leak, which I've been told most do...

Cross posted from the diesel section. For Sale - Complete, Low Mileage 2L-TE in NW Montana

SOLD I just pulled this running 2L-TE from my Prado at 70,536 miles. It is complete from the fan to the bell housing, and includes the ECU and all of the associated wiring plugs (would have to be reconnected). The bell housing will bolt directly to any pre-1995 V6 5-speed (post '95 will require...

One of the sweetest running engines I have ever seen. No overheating problems, and good oil pressure. Engine is still in the car so you can test it yourself. Car is fully driveable. Miles on the car show 250K, however an old engine does not purr like this one. 1997 engine can be used in...

Hi guys, Currently on the hunt for a running 2F engine for my FJ60. If anyone has any leads or connections to one for sale it would be much appreciated. Located in Texas but open to having it shipped. Thanks!

I am in need of a 3fe to replace the one in my 91 fj-80. This is my daily driver i just purchased it this summer. Im located on the north side of dfw. Have cash in hand and can pick up my self if your in texas or within an 8 hour drive of dallas. Being a pedestrian in this area is killing me...

$500 For sale is as far as I can tell complete 2F motor. Unknown year I was told 1976 Comes with all accessories, emissions look to be intact. Nothing is cut all wires are there. I purchased the motor as a package with a 4 speed I needed. Motor and trans were already pulled when I bought it...

Hi guys! Its been a while since I did any posting on here. So here is a quick update. I have a class project to rebuild my tired 2H. I tore the engine apart last summer and brought my camshaft over to vancouver to measure the camshaft lobes and found that they were all worn out from the...

I am purchasing a 2003 LX470 with 116k miles. I will pick up the vehicle next week. Please tell me what items I should replace, change, inspect for wear, etc. to get it ready for its new home. I know the timing belt was replaced at 90k miles, and I assume the water pump at the same time...

320k miles. Now what? Rebuild or 5.3 vortec?

Shipping available for most parts, but not for fenders, hood, doors etc. Grille and bumper apron (panel below grille sold). All other body panels ( hood, fenders, doors, tailhatch,tailgate, flares, bumpers in VERY Good condition with clearcoat peel, but NO RUST Seats are manual and cloth and...

I am having my FZJ80 (1993) engine rebuilt. A friend advised me to NOT let the shop rework the cams, but to order new ones. A pair are about $1k right now. With the rebuild already at approx $4k, that is a huge chunk of the budget. He claims there would be a HUGE loss of power, and that I...

Hey guys, Anybody heard of a place that modifies ECU's for the 2UZ-FE engine that strips it down to the basic essential engine functions? I'm hoping for an ECU stripped of the immobilizer, emissions, and other uneccessary functions. Any leads? Thanks! -Kyle

Going to be home at my parents for Christmas and would like to replace the seals and gaskets in my 2f engine (she done sprung a leak). Neither me or my dad have pulled an engine before. We would super appreciate it if anyone would be willing to come lend a hand. Thanks, Andrew

Hi everybody, I'm new to this forum and i just bought a fj60 converted to 2h, but the engine mount that are welded to the frame are not from a hj60 and it is poorly made.... I would like to know if one of you have or can cut and sell engine mount (bracket welded to the frame) from a hj60 with a...