On my pop's 2014 land cruiser, when the headlights are on low beam are the outer lights the only ones that are supposed to be on? When I put the high beams on the inner bigger lights come on. Thank you
Hello,
I have an issue with my 78 40 not being able to turn full lock to full lock. I restored this vehicle meticulously but this is the one area that I consider a hack job. I put on the 79-83 mini truck power steering conversion. The problem is that I have a 1 1/2" body lift so I have...
Hello,
I just purchased a 2020 Tundra TRD PRO, and been trying to find a TRD cold air intake. Even the dealer is saying Toyota hasn't come out with a part number for the 2020. The last part number I could find would be PTR03-00140. Does anyone know if there has been any changes in the...
I'm having a problem with my rear drum brake, passenger side on my 94 4wd pickup with the 3.0 V6. I was trying to contract the brake shoes so I could get the drum off and instead I went the wrong way and expanded them to the point I can't turn the drum at all. My first question is now that I'm...
Hello,
I'm having a hard time finding a hand brake switch for my 78 40, it doesn't seem to work no matter the adjustment until I'm driving down the road and then it decides to come on lol. Also, my heater blower motor top hose (corrugated) has fallen off due to deterioration. I'm having a...
Any suggestions on where to buy an 89-95 rear double tube bumper? I need it to have a receiver for towing. The only one I see is the trail gear rock defense. I don't really need it to wrap around the rockers. I was hoping for a couple choices.
I'm hoping someone here has done or can please give me some insight on a clutch job for 94 4wd 3.0 v6 extended cab pickup? I'm hearing two different ways and one has the engine coming out which i'm desperately trying to avoid. Thank you
I'm looking for a windshield frame for my restored 78 fj40. I would need a 78-84 that accepts the larger motor cover and the squirter on top of the frame.
Could someone please tell me how to test an fj40 rear heater motor outside the vehicle? Can I use a 12v battery? It has two wires, the white with black stripe that grounds to the bottom body of the heater and a blue wire. Thank you.
My 94 3.0 V6 pickup needs the typical head gaskets. They were done under the recall back when the truck was young but they now need to be replaced again. My local Toyota parts guy will give me a discount on parts but I was hoping for some input here. Should I get the OEM gasket set or is there a...
Because of another issue I posted, I pulled out my MAF to check the contacts..STUPID! and i'm having all kinds of trouble putting it back in and now I'm confused on which three contacts go to which prong. The truck turns over but will not start. I've posted pictures. I'm not sure if its normal...
I have a 94 4wd deluxe extra cab with the 3.0 v6. I'm having an issue that just stared. when accelerating at higher rpm's it seems to have a slight buck almost like restriction, like it wants to keep accelerating then holding back a bit and so on and so forth. It seems to idle fine, maybe a...
I'm replacing the thermostat housing gasket on my 78 2f because it was seeping coolant, the roundish one, not the one that mounts to the head. I thought I had one but the one I had , the holes didn't match up that good so I made one out of hi temp gasket material that's 1/32" thick, it says it's...
Could someone please explain how the brake master cylinder on my 78 fj40 operates with the two reservoirs? The reason I'm asking is I'm replacing mine with an new OEM and I'm bench bleeding it. The smaller of the two reservoirs seems to pump much more fluid than the larger one. I'm doing this by...
I'm replacing the brake master cylinder on a 78 fj40 due to a leak between the booster and the master. I'm replacing it with Genuine OEM part. I'm not sure how to check if the rod needs to be adjusted and if so how to, to the correct spec. Also, I've seen conflicting opinions on wether or not...
Obviously I am computer challenged, I can't seem to find the FAQ section anymore. I know I've seen the 2f head gasket OEM part numbers and the different years. Would anybody happen to have that listing? Thank you.
I'm going over all of my grounds and I'm not sure if the two wires with the eyelets go under the bolt before the plastic fuse box or on the back side of the box after the bolt goes thru the box? Either way, with the plastic how is it being grounded? Is it because the eyelet makes contact with...
I posted this in the wanted section but haven't had a lot of feedback. Would anyone happen to have a 81-87 2f #61040 cylinder head? My demonized fj40 has a crack in the head.
I'm looking for a later 2f head. I have a 1978 fj40 but I'm using a later 2f head (61040) because of running flat top pistons instead of the original dome headed ones. it now has a cracked head that needs to be replaced.