Search results for query: *

Forum search Google search

  1. E

    LANDTANK - SUPERCHARGER

    When will your IC setup be available? Have you had a chance to test it? Looking forward to hearing your results.
  2. E

    LANDTANK - SUPERCHARGER

    Nice work! Any news on when your IC will be available for Magnuson owners? Btw, any ideas on how to mitigate the heat soak considering the IC is partially over the ex manifold? Thanks for the update.
  3. E

    LANDTANK - SUPERCHARGER

    Nice work! Already popped my NOS blower on. Any updates for your IC options for the TRD blowers? What do you anticipate your blowers to be at hp/tq wise over the TRD ones?
  4. E

    Confidence check on front pass wheel bearing/spindle R&R

    Forgot to mention, the oil seal after 14k miles (I replaced the spindle after the bearings 26k ago) did put a decent groove in the spindle surface. It did its job, hoping to migrate the new oil seal for a new lane. I don't mind throwing money at this rig, just trying not to waste it. I've...
  5. E

    Confidence check on front pass wheel bearing/spindle R&R

    Yes, I believe this new spindle I popped in has the new roller bearings. Thank God for google sheets, that was 8 years ago 14k earlier. I'm hoping its not the needle bearings at 14k. It is bizzare on the corrosion spots, my hub was packed with CV2.
  6. E

    Confidence check on front pass wheel bearing/spindle R&R

    Appreciate that note, I'm on 35's at the moment moving to 37"s. My new protocol!
  7. E

    Confidence check on front pass wheel bearing/spindle R&R

    Haven't felt any lip on the race where it interfaces the spindle. One thing I did notice that the inner race does not fully engage all it's surface to the spindle. As if it only pushes back and covers 75% of the race/spindle contact surface area. I've attached a couple images with the green...
  8. E

    Confidence check on front pass wheel bearing/spindle R&R

    Appreciate the feedback. This is what I didn't do, after my axle/knuckle rebuilt I never came back to check the new bearings. Note taken as with my low mileage I've only done one full axle rebuild on this rig. Thank you!
  9. E

    Confidence check on front pass wheel bearing/spindle R&R

  10. E

    Confidence check on front pass wheel bearing/spindle R&R

    In need of a peer review/confidence check on my 97' 80. I've got 131k on the clock and did a R&R on the front wheel bearings at 105k. ...So basically these front passenger Koyo's have 26K on them. New spindle was installed at the same time. About 50miles ago, I was getting what I perceived as...
  11. E

    LRA 24's/4x4Labs/3"exh Q's

    Awesome, I hear you on the whistle lol. Seems like most on mud that have removed their resonator ends up putting them back promptly. I recall seeing a photo of someone that had a V-band tail section that could be removed when wheeling. I'll post some pics as well once I get this sucker up...
  12. E

    LRA 24's/4x4Labs/3"exh Q's

    Copy on that one. What did you do to fit the 24 onto Lukes bumper? It seems most are doing a angle iron bracket welded onto the crossmember? I'm hoping and wanting to incorporate some kind of small resonator before the tailpipe section. Got to take some measurements on what Corsa has to...
  13. E

    LRA 24's/4x4Labs/3"exh Q's

    Ah, looked at the undercarriage again. The up and over the crossmember is BEFORE the tank. Thanks for the double check! On a side note, looking forward to what you come up with on the Squadron/ARB flush mount pieces!
  14. E

    LRA 24's/4x4Labs/3"exh Q's

    There's quite a bit of threads on LRA 24's and the mods to Lukes bumpers (depending on design) on mud. Anyone, with a 3" exhaust with this combo? Trying to figure out whether to do the exhaust first or the 24gal Aux tank? Would love to see any photos or comments on people who've had this done...
    • eric90503
    • Thread
    • 3 inch exhaust 4x4labs lra lra 24s vehicle tech forums
    • Replies: 10
    • Forum: 80-Series Tech
  15. E

    Collector edition/40th Black Pearl badges

    Yes Sir, keep us posted
  16. E

    Collector edition/40th anniversary trim

    Lets go!
  17. E

    Wanted 80 Series JDM Auxiliary A/C Condenser Fan Pigtail

    What ever happened to this project? Is this it? OEM non-usa JAPAN spec. Radiator & Condenser Electrical Auxiliary Fan HARNESS SIDE Connector Plug & Terminals / Seals KIT FJ40 FJ55 FJ60 FJ62 FJ80 FZJ80 HJ80 HZJ80 HJ81 HZJ81 - VintageTEqParts.com -...
  18. E

    Help with Supercharger brass elbow hose location

    Does anybody know where this brass elbow hose is supposed to go to?
  19. E

    INSTALLING A SUPERCHARGER… AT 239k MILES… IN 2023.

    Nice looking piece. What's the reasoning behind this? The machined lip?
  20. E

    INSTALLING A SUPERCHARGER… AT 239k MILES… IN 2023.

    Great thread TNFZJ. Was just thinking about this. Mine is still in the box about to be installed. How's it coming along?
Back
Top Bottom