Hello, Im selling my trailer that is it excellent condition. Ive had it for about 10yrs but only used it a few times. I dont know much about it compare to most gurus on here. I added a receiver hitch and a top rack with hyraulic lifts. Plywood needs replacing but everything else works perfectly...
So here is a short video of us wheeling to our camp site in Southern Arizona with the M416 and my new trailer mods
m416 trailer lid rack and water cooler holder Land Cruiser FJ 80 custom builds - YouTube
So here is a short video of us wheeling to our camp site in Southern Arizona with the M416 and my new trailer mods
m416 trailer lid rack and water cooler holder Land Cruiser FJ 80 custom builds - YouTube
I have a 97 Cruiser and want to know if the alternator is an "internally regulated" Nippondenso with remote sense? if so, the instructions for installing isolators requires a fused lead from the ignition wire to the E post on the Isolator.
thank you very much for the help
scott
Im selling my winch since I never built my bumper. I am the original owner and it's never been used for installed.
please call or txt instead of replying if you are interested because I wont have access to internet for a few weeks.
thank you very much,
Scott
520-591-8969
I feel it's very important to let everyone know to what extent Charouleau Gap is getting renovated.
here is a quote from the Nation Forrest Service Dept Engineer that is heading up this project:
"to smooth it out enough IN ORDER TO GET A 'STOCK' FULL SIZE, 4X4, DUALLY, CREW CAB FOUR...
I went to the Gap twice this week and there is a construction crew with a D-6 dozer, back hoe, and a huge track hoe hired to take all the rocks out and make the trail easy for a regular 4x4 to access it. i have searched for info about this and cant find anything about it.
if you want to...
I just connected a Hopkins/Hoppy 48845 wiring harness at the end of the old wires that were already on the hitch. I never tested the wires before now.
After splicing the 5wire Hoppy to my 4flat, i still have no power. I dont' even have power at any of the wires coming over the truck using a...
I am trying to wire a trailer wiring harness at my rear bumper and I can't get any power through any of the existing wires.
the old outlet on the truck is gone so all if have is the loose wires
any help is much appreciated. i have wired a lot of chevy trucks in the past and this is my first...
Hello, I am replacing my exhaust and I need two new weld on flanges so I can bolt up two new O2 sensors.
Does anyone know where I can purchase these? Toyota says I can and no exhaust places in Tucson,AZ say they can get them either.
Thank you very much in advance...hopefully cruiser Dan is...
Does anyone know which vacuum line goes to the intake that will best distribute to all cyclinders? I'm assuming the pcv line but want to check with you all first....thanks
Well I just opened my the box to my new winch to test the air compressor functionality:
It rocks.
I just inflated a 35 MTR on stock a 16x8 rim from 11.5psi to 39psi in exactly 120 seconds.
Hello, I replaced my EGR valve, clean the tip of the flow sensor, reset the EFi, and the engine light came back on saying insufficient flow again.
Does anyone know what I can do next?
thank you very much!!
Hey there, I in route to Moab in my 97 FJ80 for Th, Fri, and maybe a trail on Sat as well. if anyone would like to meet up I will be there later tonight. I have been 14 times, mostly in full size blazers, suburbans, Wranglers, Cherokee's, and now I finally have a cruiser and it is ready to...
1997- FJ80. I am installing my knuckle and trying to hammer in the top bearing cap and I still have about an 1/8th to go for it to press in the bearing. The manual calls for an SST tool to support the inner race. I don't want to risk just cranking down the bolts to press it in w/o suporting...
Hello, does anyone know if the center bolt heads are 12mm? Also, if mine are rusted on, does anyone know how I can remove them w/o sawzalling them off?
thank you very much