When I had my alignment, I had a full tank of fuel. Got the specs on. Now when the lc has a full tank of fuel to about 3/4 tank all is ok. No pulling and feels right. However, when there is less fuel i feel it starts pulling to the right.. What gives here??
My 200 does not have the power folding.. now I feel its one of those features I think I would like to have... anyone tried retrofitting.. my 200 is the vx so I'm thinking the wiring for this feature might already be there and it's just the hardware that is needed... I installed the auto...
In a scale of 1 to 10 this is a 2.
Steps:
1. Remove old fluid by sucking out from reservoir.. i used a big syringe... get as much without going below minimum
2. Fill up with new brake fluid.. i used the new bosch brake fluid. Compatible with dot 3, 4 or 5
3. Turn on ignition. Start bleeding in...
im looking to change my shocks to bilsteins.. the fronts are 24-214018's but i am confused with the back ones. there are 2 part numbers 24-152938 and 24-269049.. anyone know what the difference between the two part numbers? thanks bros
After I got my 2018 lc i soon had the springs replaced to US Version springs... the dealer did the spring replacement. However I immediately noticed there was a slight lean that the dealer obviously said none and released the car to me... I never got over the slight lean and tried the blocks...
I count 3 empty sockets located at the rear of my 2018 lc vx. I saw these when I popped open the drivers side rear panel to access the power socket... what are these for? I'm guessing for an inverter perhaps for the units with either 110v or 220v outlet? But I'm guessing here... ideas? Thanks bros
Our fog lamps look like they barely shed any light...I’m sure they have perfectly located beams, but I was thinking of replaceing them with brighter units... are there plug and play units there that perhaps give off 15k lumens each side perhaps?..or brighter more penetrating beams...
ANybody has experience when it comes to removing the front grille of the 2016 later lc’s? I removed the cowl and the 3 screws and the 3 clips at the base.. the grille seemed to loosen but the front chrome mounding that go in front of the headlight would seem to prevent removal.. I’m guessing...
After changing the rearsprings and adding oem front spacers, I still want some 3/4 inch of front lift to get the stance I want.. what is the best economical suggestion to do this without sacrifing alignment and the stock ride quality... also don’t want to change control arms..best also if we can...
I felt how the complete set, front and rears, feel and it’s a bit too stiff. The rig handles way better but ride comfort is compromised.. I a man now thinking that the ride can be improved yet still have better handling with simply replacing the rears... has anyone tried this? What is the effect?
I remember there were test and all to develop a new set of bilstein shocks for our rigs... someone here was shouting out the need for test rigs etc. has anything come out of that? So sorry been out of touch but maybe we could refresh this idea and we could check out the new products.... thanks...
The series 200 specifies dot 3, some owners had bad experience using dot 4 pedal staying mid way etc... can someone elaborate? Is this true or a myth. Cap on my 2018 says dot3 or dot 4
I was trying to get the ambient light mod on my lc and I saw this empty hole. I’m sure there I see a part tha is missing that can easily be installed.. Mayberry our friends can chime in...
2018 lc has smart remote but the interior light does not turn on brightly when door is unlocked either with key fog or door handle. The interior lights light up but it’s very very dim. The customization has interior lights set to turn on when unlocked. It is even set to Light on when approached...
I saw these empty sockets in my tailgate. Anybody know what these are for? Maybe we can retrofit and make full use of the wiring that's already there...
i think our rigs have configuration codes that let the factory set the options for each rig. some of the options are not configured even if the wiring are all there. is there a way to get these configuration codes? if i understand it right this is going to be an extensive thread. I think moving...