Has anyone hooked up an oil cooler to the 2010+ model with the cartridge? Thinking of just a decent sized heat sink set up with thermostat, dont want to stack a finned cooler in front of the radiator and decrease the cooling capacity of that
I thought id share something with you all, couple of months ago i had a code from my ultragauge, (cant remember the number) but when googled saying throttle stuck open which put the var in limp mode. I had a planned to on a 1000km round trip that weekend which i did not want to miss at it was a...
So my engine had been behaving wierd for a couple of months, i finally got around to checking the maf sensor on tuesday as i had the day off work. Upon opening the lid to my airaid intake i seen the filter had slipped off the mount and was loose in the box. The pipe and throttle body were...
Front lca replacement, my my front lca bolts are siezed and im looking at replacements, unfortunately dirtking, camburg and tc are out of budget which leaves me with 3 options. Superpro double offset adjustable, superpro standard offset or these ones ibe just found from hurricane performance...
So i have this problem for a good couple of months now. With the car sitting at idle usually once warm the rpm will fluctuate, this happens with no A/C so rule that out, warm battery voltage holding 13-13.4, with the vehicle off battery is at 12.7-12.8.
Sometimes its only a couple of hundred...
So i recently installed 1.0 inch thick spacers ontop of my fox 2.0 coil overs, the preload was backed off by 1 inch to keep the lift as close as possible to what it was before. Ofcourse this was causing some binding. The left hand shaft is a standard aftermarket shaft as its all i could get...
So it seems i have the usual play (and quite a lot) in the left side of the diff where the cv joint goes in.
Going through my options and i quite like the idea of the nitro wormdrive, wat id also like to chuck in while the diff is appart is a stronger 3.73 ring and pinion, i know i can get the...
Just wondering if anyone has actually measured the fox 2.0 coil overs from center of eye to base of thread as fox measure from the top hat. Nees to no compressed and extended from the standard measuring points. Not foxes advertised
So i need some help. I have to noises. One is a clacking sound in the front when turning but not like a cv joint sound, its not consistent enough and also happens moving backward or forward at crawl speed, once moving strait it goes away also happens over bumps.
Noise to is something in the...
So ive been running with no front swaybar for a few years now but Am curious if anyone has found a lighter/softer front sway bar for the fj cruiser? Seen a few stiffer ones and i believe total chaos do a softer one for their lt kit but not stock length.
So over the coming year im hoping to start building a worked n/a engine.
12.5 compression pistons
forged rods
Custom heads
But im having trouble finding a used short block for the 2010+ fj.
Does anyone know if a blank block (no internals) from the earlier model is the same fit.
So having an oil pressure gauge in the fj, at around 2000rpm highway and 100kph i normally see 40-43psi, these last few weeks i seeing 30-35psi. I just had it serviced a few weeks back so wondering if its possible that a different brand of filter (genuine) and a different brand but same...
So im hoping someone has an idea here, ever since installing the new rear suspension there has been a thump over higher speed impacts. It only seems to happend when both wheels go over a bump at the same time. At skow speeds its perfectly smooth, i can flex each side out completely with no...
There is a lot of discussion about cv bind and strut length online but i cant find anything about tie rod and rack end limits, has any body tested the max strut length for the factory steering components?
Can someone help me out with this, the rear shocks i want to use are 410mm compressed length, with standard bump stops you would space them down 45mm (2 inches) to account for the length, but im running timbren rears stops, the metal bracket is 35mm tall giving me a safe compressed length of...
Does anyone have any experience with the trans go kits? I was originally looking at a valvebody upgrade from wholesale auto but the shift kit wont come to anywhere near the total cost of a valvebody upgrade.
The only downside i can see is that the wholesale tc lock up kit wont lock up in first...
So as im still looking for a bit more n/a power and am heading back to my tuner in a few weeks to have some gauges installed i plan on having this discussion with him but thought id ask here before i embarass my self.
I dont wanna hear JUST BOOST IT as by the time i manage to save 10000aud my...
Alright so when i ordered my lightwieght water pump pulley it came with a matching alternator pulley option so i ticked yes, of course it was only when i went to fit the alt pulley i realised the fj has a decoupler pulley, basically im just wondering if its possible to swap the decoupler to a...