Search results for query: *

  • Users: bhsdriller
  • Content: Threads
  • Order by date

Forum search Google search

  1. bhsdriller

    FZJ80 Fuel Filter Part Number differences

    It's been a while since I changed one last but ordered the 23300-69045. Opened it and the filter inside has 23300-66040 Anyone else run into this and is it correct? Don't have the old one off yet to compare it to
  2. bhsdriller

    SOLD  Central Ca: 1994 80 series, lockers, white all stock

    Posting this for a local friend. I did all of the work on it recently probably within 500 miles. Runs really good no problems there. Maybe some slight surface rust underneath but it's been in CA for a long time. Looks like the front driver fender was repainted at one time, driver mirror has been...
  3. bhsdriller

    05 vvti camshaft position sensor wiring

    Not getting any hits in the 4runner section but they use the same engine so hopefully someone can chime in here and they might be the same. Was doing a timing belt and ripped off the plug coming from the harness that connects to the camshaft position sensor on the driver side. What I need to...
  4. bhsdriller

    4th gen 4.7 v8 Cam Sensor Plug Wiring

    Need some help should be simple if someone has a plug they can look at. This got ripped off when doing the timing belt, taking off the driver side belt cover. Need to know which wires coming out off the harness went to which pin so I can put a new one on. The new aftermarket plug has wiring...
  5. bhsdriller

    Factory locker order of operations

    80 in question is a 94. Main question is will the front locker actuate without the rear? This is in 4L of course. First turn of the dial and the locker light just blinks. Second turn the locker light turns on and goes solid. Can the rear lock but the light keep blinking? If so what is a...
  6. bhsdriller

    Factory installed supercharger?

    I've searched and couldn't find anything. Were all TRD superchargers added on at a dealer once they arrived/aftermarket here or did any get factory installed?
  7. bhsdriller

    20R Carb Help / General Carb Symptoms

    Have a 77 Hilux with a 20R that isn't running right and I have some general questions. Rebuilt stock carb that starts right up, idles fine and I can rev it all day long at idle. It drives good at slow speeds but when you try and get on the gas it sputters and doesn't like it. Cuts out with...
  8. bhsdriller

    Aisin Carb Help

    Ok so up front this isn't for a 40 but on a 77 Hilux. After re-building they are very similar so maybe one of the experts has an idea on where to look. With it running and the fuel half way in the window i'm getting fuel leaking out from between the top and body. Basically around where the...
  9. bhsdriller

    77 electric fuel pump / carb leak

    77 hilux with a 20r that has the in tank electric fuel pump. Are these supposed to have any type of return line/valve back to the tank for when the float closes the needle valve? It all works, fuel comes up in the carb to the half way point but then it will start to seep out from between the...
  10. bhsdriller

    77 Hilux Vacuum diagrams/smog help

    Truck is a 77 hilux with the 20R. Longshot but does anyone have or know where I can get some diagrams for this? One on the hood is worn down Just rebuilt the stock carb Trying to go from a weber back to stock for smog. It has all of the smog components just need some help on the main vacuum lines.
  11. bhsdriller

    Broken Vacuum Port, PN Help

    I've searched but can't come up with anything, probably not calling it the right part. Anyways does anyone know what it's called or have a diagram? Thanks
  12. bhsdriller

    Bypassing ballast resistor / Operation

    Have been having a no-start issue all of a sudden. Can I bypass the ballast resistor and wire the 12v switched right to the + on the coil? Reason I ask is I tried it and the cruiser started right up but ran super rough. Wouldn't idle at all and then died I have also read about people putting...
  13. bhsdriller

    Valve cover nut/washer differences

    Need some help. Searched a lot and thought I was ordering the correct washers but when I got them in they were way too small and the nut won't thread on. Left is obviously the old with the wider ID allowing the nut to thread on. Second pic shows the new installed
  14. bhsdriller

    PSA: Check your caliper bolts

    Heard a grinding all of a sudden on my way home from work. Only lucky thing is that the bolt was just chilling there. ~4k miles after replacing rotors and pads including a trip to Moab
  15. bhsdriller

    Windshield Sunshade

    What are people using, any brands or recommendations? Searching and see some that say they make one but not really any reviews. For a 75 btw
  16. bhsdriller

    Can't get E-brake adjusted

    New rear pads and rotors, parking brake pads were fine. Adjusted out to where they're just touching the rotors and can't get any kind of stopping out of them. Maybe the cable is stretched, is there a way to adjust that out? Do you do it at the handle side or at each wheel?
  17. bhsdriller

    SOLD  80 Series Spare tire assembly / Bakersfield, CA

    Completely rust free and operates fine
  18. bhsdriller

    FREE  Stock FJ40 Springs / Bakersfield, Ca

    They're rough but someone might be able to do something with them before I take them to the dump. Set of 4, can get pics up later.
  19. bhsdriller

    FZJ80 installing rear axle after rebuild

    Searched but didn't see anything specific. 95 with factory lockers, rear axle locked before I took it apart. Passenger side in question, after an axle seal rebuild can't get the axle back in and seated all the way. Anything special i'm missing? Can feel the splines engage and slides in then stops.
  20. bhsdriller

    Removing heater core from case

    On a 75, stock front heater. Any tips or tricks on removing the heater core from the case/mount? Does it just slide in/out, I assume it's just stuck
Back
Top Bottom