J Mack's latest activity

I got the chiller and got all of my TIG torches assembled so I can quick change between them... I've actually been pretty busy between building a fuel injection system for the Diamond T, redoing the cooling system to remove some Chinese on the...

Any updates on dis here Booger Green shananigans??? Oh 😲😳😮 did I spell dat right??? Like I give a **** 😮😳😲🐖👈😏😘🤣🤣🤣🤣

Why wait🤔🧐😉???

new site to print from , 3D model community. Search & download free 3D models. Share 3D models - https://thangs.com/?sort=trending . i imported the gear file over and ordered one to see if it will replaced Shapeways ...xtiaan2000 . sent a pm i...

Made in Newton Ma. U.S.A. Imagine that 😏😘

Yes you are correct but there are a few work arounds.. I have this old dinosaur that I believe I've had for 35 plus years, they were quite expensive when they first came out but I felt it was worth the money for what I was doing at the time...

Nor will I support China Mr. STARRETT (did I spell that right) do a little research on them 😏😘🐖👈

Sorry if I hurt your feelers, Bob. Edit: Nearly every brand has a “name brand” product line manufactured by the actual company, and then a product line that’s outsourced to other companies. Mitutoyo has manufactured in Japan for the name brand...

Different peeps will have different settings every single time. The chart is a starting point and adjustments are made from that baseline. My opinion on the videos with the settings so low is it's an open corner that looks like minimal to no...

All I have to say : - We have Miller 255s up at BIO, and I just leave them set to whatever they were set at. 💩is confusing, yo. Also, I produce software for my “real job”, and I fear getting distracted and annoyed by some obvious flaw in the...

Ready to go. (It’s the same truck! 369 days elapsed between these two photos.)

I have so many questions why a guy with his talent, budget, timeline and resources would do that but I know now is not the time.. Maybe we’ll be at the same camp site sitting around the same camp fire some day and we can talk about it while you...

Sounds like it’s time for a LS swap, just make sure you weld those motor mounts in really hot on the vertical welds and you’ll be good to go.

While not as old a tin, my wife was going through some boxes from her folks and found this, I told her the timing was spot on. Added to my shelf of antiques in the shop

Headed to powder coat

So was getting things ready for fuel system ( shut-off valve, fuel water seperator filter etc.) And decided to fire 1 more time before tearing into it. Bad idea, was running fine rpm's increased on there own started making funky noises shut it...

Tackled the differential seals yesterday afternoon and this morning. New seals, slingers, deflectors, pinion nuts, and washers. Along the way I discovered that the current Toyota pinion nuts are 27mm vs the old nuts of 30mm. I had one of each...

https://cruisertrashparts.com/products/55-series-rear-window-gear

Splash Screen while the Haltech loads. Way better than bright yellow HALTECH in your face And then the center section. Switch Pro, AC Control, Wipe/Wash, Hazard, USB, Dual Battery and Ham Radio all accented by the original Land Cruiser Emblem

Got me some new stickers, swag and a copilot from @samc2447

man, if he started *today* I'd be 80 by the time a grandchild was 16. and you're welcome to do so. be aware that I run a very large open source project, with over 1m installs and people on the internet hate me. I'm serious, ask @PabloCruise...

Pump arrived today, early and in good shape. I emailed the mail service in Blaine stating the package had my last name misspelled and after lunch I got the reply it was there, so a nice win on our BC Day Holiday up here. :beer:

I don’t think I’ll pass a test after but I feel like I’m learning in here, thanks to those sharing some knowledge. Jim I love reading the bit about grandkids, our 2 kids are up helping my folks at the ranch and making memories that will last a...