dogdaysindurham's latest activity

^ Yes, that's the one I saw. But OP, since you'll likely need 2 of those, if you want this to look tidier you can get essentially multiple of those connectors in a block plastic housing. May look better and be safer. Surely quite a bit...

Just got it in. We use these in both of our Trophy Trucks. One has a dual alt setup (redundancy, also has two starters and two of most every other critical system). Here’s some engine porn as well.. Should be able to install next week.

I think I'm finally pull the trigger on this unit. My house comp died & my ARB twin just can't handle the volume. ~~~ edited 9-25-25. Mine arrived today!!! For those that are going tankless...Puma sells a tankless air compressor. Puma 3/4-HP...

A good week for bumpers and sliders. Thanks for the continued support fellas! @NCFJ Sent you an email with your pics. J

@e9999 is right. I have used this before and slide on some adhesive heatshrink over the top. https://www.homedepot.com/p/Commercial-Electric-14-2-AWG-Aluminum-Dual-Rated-Splicer-Reducer-2-Pack-G61101HD/310741687

not like that, bigger, chunkier, and with holes where the wire is squeezed instead of a top screw like in that pic. Think breakers. Google Electrical wire splicer/reducer or something like that, HomeDepot has some big inline ones IIRC. A...

I have the XV-2 and can drive an atv up into the bed with the platform raised to the high position. I have had this for 1 year, bought it used and so far th eonly thing I would change on mine is to go to a james baroud hard shell tent instead of...

Looking to sell my Schutt industries XVenture XV-2 Deluxe Plus - it's honestly seen < 10 trips. I purchased it 18 months ago, and it's just not quite right for us, so looking to move it on. Makes for some great social distancing, as this is built...

nice trailer. GLWS. My bro has one and he loves it... My bro has one and he loves it..

I contacted them a while back and this is what they sent me. hope this helps Dear Juan, Thank you for your email. XVENTURESevere-Duty Trailers are in-stock ready to ship once we have your color selection, hub pattern, and accessory set. It...

2019 Schutt Industries XVenture XV-2 Located in Denver, CO Asking $23,000 I'm willing to drive to meet you within 5 hours of Denver, CO. The trailer is in great condition with several accessories and useful modifications. Garage kept/stored and...

I’m reluctantly putting my 2015 Schutt XVenture XV-2 off-road trailer up for sale. This is the bigger model of XVenture trailers. The bed is big enough for all your gear, motorcycles, or a 4wheeler providing the ultimate backcountry basecamp for...

Where you overcharged ? Did Dissent refuse to refund you if you were ? . Or did you just see mistakes on their site and point them out? Then were not satisfied they did not fix the in a time frame you liked ? Dude most Land Cruiser company's...

Not to concerned with the warranty. Its been in 4 times for a vibrating jack and they forgot to center my steering wheel after an alignment. I have a receipt for 0-20 from a previous oil change where the vehicle still vibrated. I would no...

Many have asked if I will make a rear bumper that matches the design and high clearance of my 80 series Cruisin bumper. Started the bumper this morning and hope to have a finished product soon. Rear crossmember does not need to be removed, but...

Renaissance Auto Care In Cary did a great job with my 2000 LC timing belt job. They were cool with me bringing a Aisin kit from @cruiseroutfit and a OEM thermostat. Finished the job in an afternoon and for a decent price. I sent a buddy of mine...

Exhaust is sounding better after a break-in period of varied driving. Drone is worst at 1800/rpm. Sounds awesome at WOT!

Update: installed the Revel Medallion exhaust on my 100 series. Worst part was removing the 25 year old rusted hardware from the exhaust flanges. Had to bust them off and of course the bolt extractor set I bought at harbor freight skipped the...

yes. we sell a cross bar kit to add extrusion cross bars across the top of your OEM rails. Can be done in any length, I think that's what you're after? Our wing brackets are a direct bolt-up, here's a pic:

There is a drone at around 2k rpm as it doesn’t have the second muffler like OEM which is tolerable. The build quality and welds are excellent.

I recommend the CSF all aluminum radiator

That is an interesting idea. I have only seen the rear window side molle panel kits (Ohana Rig Supply?) that work with OEM rack but not a drop in replacements for the factory crossbars...

Is anyone aware of a crossbar kit that utilizes existing OEM roof rails, like this one from LFD Offroad? Ruggedized Crossbar Kit - 4th Gen 4Runner -...

27mm is 90% stiffer than a 23mm AHC bar and 60% stiffer than a 24mm non AHC bar.