LandCruiserPhil

Globe/Miami last night at 8PM and this morning at 2AM road is clear but still lots of damage.

Winch hill 4 was a tuff son of a bitch but all three of us made it without winching. Literally asked for the hook, but nobody heard me so I thought I would give it one more try. Add to my surprise, she pulled right up🤠 List time it was hard at...

Those look like the interior swivel brackets for the optional flux capacitor. Very rare.

Nice to see a new product.. FWIW the fan we used was from an early 100 series. The only reason we stopped was that we could not get DEPO to produce enough. We would run out every year.

It's wired on with the ignition, so key on = fan on. There's a temp sensor in the harness that will shut the fan off if it's below 60°F ambient. If you need to shut it off manually, there's a fuse on the relay that can be pulled. *edit- I'll...

Is the fan manual on/off switch or temp sensor activated?

OK, fellas... I've got two boxed up and ready to go. $215, shipped in the lower 48.

Just ordered deltas!

↕This↕ or get out the grinder.

Well life has been really busy ! I'm supposed to be retired or semi retired or something like that 😂🤣 but it seem that I have been busier then when I worked full time. Anyways when I got home from SAS I did not have time to check out my rig. In...

3,000 miles of mostly highway? Nothing except gas money

I don't have an adapter for that brand... BUT we do have a system for the 80 series that bolts in place for the 80 with a few options for mounting the rear camera as well if you have a tire carrier or not. 🤘...

Working on a couple prototypes for bolt on front and rear diff armor. Made out of 1/4" steel. These are good insurance pieces. Easy to install, still have access to the drain and fill plug, works with the factory drag link and sway bar. I'm...

I had time on my hand and decided to operate on the charcoal canister-LCP hack! Per @LandCruiserPhil instructions.

I have done a lot of remote solo travel, and the only major parts I carry for an 80 is a fuel pump and a PS high pressure hose. (never needed) You can work around a lot to get home, but without a fuel pump, you are not going anywhere.

OK so the removal of the filler neck from the donor is complete. I must say that it was easy but time consuming. If you go into the job understanding this, it makes the job much easier to accomplish. Here is a list of a few things that might...

I installed a used fuel filler on mine in 2020. The old one was able to come out in one piece, the replacement was cut. I reconnected it using 1.5 inch fuel filler hose from Napa. It was probably made by Gates. It works well enough.

I’m pretty sure the tank will need to come down or the body will need to come up.

As far as I know, you have to lift the body off the frame or get a sawzall out.

Admittedly, you are not a mechanic;, AAA is your friend. Im mechanical and I carry AAA because if nothing else it will get me to a better place to deal with the problems.

https://www.google.com/search?q=discount+tire+balancing+issues&sca_esv=64fd34011e110855&rlz=1C1UEAD_enUS1082US1083&sxsrf=AE3TifM6gK_YpLoiMZpWTSdoREcCMAzuFQ:1754832925541&ei=HaCYaODpIOyLur8P7Pul2QU&start=20&sa=N&sstk=Ac65TH4q93661fqAIsBrNCdfD4H5KRM...

Some pictures

Who makes your upper control arms?

Replaced the heim joints on my @LandCruiserPhil rear sway bar links, quick after work job to get rid of a nice clunk the worn out heims were making.

From a past Discount employee, they do not send their guys to Hunter balancing school. They teach each other the bad habits.