Tech Questions Here (24 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

lostinafog said:
I forgot one friends in high places:lol:----does anybody have the new # for the White House cause when I try I get a message "no longer in service"
Click to expand...

I was informed that the White House Offices have be moved, below is the link to reach them.

New White House Offices
 
wow im gona be on here alot! lol whats the best size for new square drive shafts?
and the new buggy has disk breaks all the way around how would i add and e break? cuz so say the rides need one ? and paul send me directions to ya shop? so i can get it looked at
 
kjnarmyfj said:
wow im gona be on here alot! lol whats the best size for new square drive shafts?
and the new buggy has disk breaks all the way around how would i add and e break? cuz so say the rides need one ? and paul send me directions to ya shop? so i can get it looked at
Click to expand...
address is

212 Bowers rd Scott

but for most GPS put Lafayette instead.

directions
north on thruway LEFT on Willow st cross over University Left on Hebert Left on Bowers appx 2500 FT green dumpster back in . if ya get lost. 235-2245
 
Hey guys, I am home now and have a few days off. I'm going to change out the fluids on the LX and my wife's Acura MDX. I think I saw some assortment packs of crush washers at Pepboys. Will those work as well as factory washers? I'd rather avoid a trip to Musson, as well as the time it will take to look up the part numbers for the washers for each different drain / fill plug.
 
moomtazz said:
Hey guys, I am home now and have a few days off. I'm going to change out the fluids on the LX and my wife's Acura MDX. I think I saw some assortment packs of crush washers at Pepboys. Will those work as well as factory washers? I'd rather avoid a trip to Musson, as well as the time it will take to look up the part numbers for the washers for each different drain / fill plug.
Click to expand...

I almost always use OEM for everything but I have used POS crush washers from the likes of Pepboys with no problems. I like the old school leather ones for the oil pan.:D I may get :deadhorse: for this post but it would not be the first time.
 
moomtazz said:
Hey guys, I am home now and have a few days off. I'm going to change out the fluids on the LX and my wife's Acura MDX. I think I saw some assortment packs of crush washers at Pepboys. Will those work as well as factory washers? I'd rather avoid a trip to Musson, as well as the time it will take to look up the part numbers for the washers for each different drain / fill plug.
Click to expand...
as long as they fit the OD of the plug .copper or alum
no plastic .
leather !! man ain`t seen them in a long long time but they be good too
Isaac you sure you be as young as ya say U B :)
 
lostinafog said:
as long as they fit the OD of the plug .copper or alum
no plastic .
leather !! man ain`t seen them in a long long time but they be good too
Isaac you sure you be as young as ya say U B :)
Click to expand...

Yep, only women lie about their age, right?

Leather is still the standard in some countries(sorta). :D
 
sparkplug said:
Yep, only women lie about their age, right?

Leather is still the standard in some countries(sorta). :D
Click to expand...

:hmm:might be like lamp shade from the hide of their enemy
 
I went ahead and got the toyota washers from Hampton, $1.50 a piece, and ordered some for the diffs, $1.10 a piece. I got a couple of OEM filters too, $5 a piece. The Toyota ATF fluid was over $6 a quart, so I passed, as well as the Red coolant, $21 a gallon. I'll go another route on that stuff.

I went to Wal-Mart and got 10W30 Mobil 1 15,000 mile oil. I had read a review of this by Landtank on mud, where he posted his Blackstone oil report. It should have no problems lasting 1 yr between oil changes. $26 for a 5 qt jug at wallyworld. The Shell Rotella T synthetic was $19/gal and the Mobil 1 synthetics were all $22/gal.
 
i did the castrol synthetic whei got the fj and it made a diff in fuel milage and i just changed it with10k on it , and it was still half clean i use castrol cuz i had good luck with the oil wihen i was on a race team oil plug fell out of bike and lasted 4 laps finished and noticed bike didnt have oil when we got back to pits ! put new oil and raced second moto!
 
NOW THAT'S THINKIN' WITH YER DIPSTICK, JIMMY!

I use that Mobil 1 Synthetic fuel economy stuff and I run it hard and long and it's still pretty when I change it at about 8k.
 
got to look and play with the new truggy , to day in the ditches buy the house notice some stuff the guy never said , #1 front axel on pass side is llike2 inches further back like it slid on spring , tie rod bent but will make a new one and sliders are made out of thin pipe looks like from lows ,,,, runs great oil looks clean , not use to the noise from the drive shafts when i put it in a bind lol use that the fj and i locked the hubs geezzz i forgot what it was like to have reall lockers nooo turnnn! but just need some tlc and it be all good! wann paint it what yall think about army green? rather than orange
 
Haha, like i wanted to do with the runner. OD green with a white star on the doors.
 
haha, sounds great!
 
put a disc brake on your driveshaft
 
I believe so. Haven't done one but a buddy had that setup on his sammy. A disc right off of the t-case.
 
What I like and will do to my 40 is a line lock. I helped Larry install it on his 40 before we went to SCC two years ago. It's easy and not to pricey. And it works great. All you do is tap into your brake line and install a small shutoff valve. When you press the brake you close the valve and your brakes stay locked in. to release just open the valve. easy cheesy
 
You must log in or register to reply here.

Users who are viewing this thread

Total: 25 (members: 0, guests: 25)

Share this page

Back
Top Bottom