Builds My build (2 Viewers)

[beachcomberspi]

View attachment 1098823 I installed the ARB Intensity 9 inch lights today

And this is going on next!!

 

[beachcomberspi]

How is the Doetsch Tec front 8385 front shocks work with the OME 850s?
Do the coils drop out with the 12.5" travel?
Did you lower you bumpstops?

The Doetsch Tech ended up sucking-too soft, measurements incorrect so I went with the Nitrocharger sport, regular length F/R and they are great with my 850/860 lift. I apologize for the late reply. Cheers!

 

[beachcomberspi]

Had it torn down. Cams look new. Machined head. Check out #6 on HG

 

[beachcomberspi]

Cams

 

[beachcomberspi]

After milling.

 

[beachcomberspi]

#6 top has some wear on it

 

[beachcomberspi]

Closer up of #6

 

[beachcomberspi]

I'm putting this here for posterity. It wouldn't fit on my signature line

 

[beachcomberspi]

Mickey Thompson ATZ 35's, Hawk HPS pads, Metal Tech 4x4 sliders, OME 850/860, Nitro 4.88's, OME nitrochargers x 4 shocks, Slee castor bushings, LandTank seat extenders, Slee ShortBus, OEM hand throttle, Aussie Locker (rear), EMS Powered exhaust, TRD Supercharger, Safari snorkel, ReMin Dash kit, Stockinteriors.com replacement carpet. My build

09/2015
ARB intensity 9" lights, Warn 9.5XP-S, HG, a National Luna dual battery setup, valve cover gasket, new plugs/wires, front axle service, front/rear main seals, dizzy O ring, thermostat, all fluids flushed and replaced, new radiator, new OEM battery and tray, new washer fluid reservoir and valves, new heater control valve, new belts, upper/lower radiator hoses, alignment and tire balancing, turned rotors and fresh pads.Cobra CB, Lev o gauge x 2 for angles. Ultragauge. New, used 1FZFE with 150k on it versus 198k on old engine. 2.6 supercharger pulley.

 

[beachcomberspi]

I added sun visors from an 03 WJ to my rig today.

 

[beachcomberspi]

New leather from super skins. Another mudder tipped me off to the kit. I'm not a pro but got in a rhythm and it will look nicer than the old, grungy, torn original!

 

[rc51kid]

What are the visors from? Are they a direct bolt in?

 

[beachcomberspi]

What are the visors from? Are they a direct bolt in?

03 WJ JEEP and they bolted right up. They rub the liner a little when going to the side but not much. The vanity lights were a simple splice.

 

[rc51kid]

Thanks.

 

[beachcomberspi]

I went both ways up to Eisenhower tunnel and Rabbit Ears pass at 65-75 mph with OD off at 3200ish rpm and with the SC didn't even bat an eye. Something in the front left axle area is grinding at times

 

[beachcomberspi]

I've added a National Luna dual battery setup. Install was a one banana job. I have an OEM Toyota battery as main and a Marine DieHard as the house battery for the winch and someday pure sine inverter and fridge as well as a jumper battery.

 

[beachcomberspi]

Adding an FYI-the NL dual battery system is fine so far. The 4/0 ring terminals wouldn't fit the large wire in the kit so I got some at Home Depot. Also the readout on the controller washes out in sunlight. Other than that install was easy and I'm mounting the controller in a shady spot.

 

[beachcomberspi]

Just ordered a couple Lev-O-Gauges. Any guesses on how much a stock 80 series can tilt in a perfect scenario before rolling?!

My build continues.....


http://www.amazon.com/s/?ie=UTF8&ke...vptwo=&hvqmt=e&hvdev=m&ref=pd_sl_7rh1rx5x63_e

 

[beachcomberspi]

Adding trouble shooting the TPS and PCV valve to my maintenance list. Along with a cap and rotor.

 

[beachcomberspi]

Putting this spring table here for safe keeping. I think my next step is 850J/863 with 37's yet am contemplating Slee 4" or Dobinson (sic) 4" also.

Cruiser Outfitters