Wanted FJ60 Manual (5 Viewers)

[cruiser_guy]

Re:G emblem

Mike,
Your entire fender is wrong! We don't have those cute fins cut into the fenders either! I may have a source for the entire fender on each side. I'll let you know in a week or two.

 

[Chef]

fj60/62 rear license plate light; 62 sway bar links

Looking for functional fj60 or 62 rear license plate light, and front and rear sway bar links. Thanks!

 

[71FJ40]

Early FJ40 Steering Wheel "Horn Seat"

Anyone have an old OEM steering wheel around they may want to sell in whole or part?
In particular I'm looking for the Horn Seat, Horn Brush, Horn Spacer and Horn contact, i.e., everthing that goes between the "Toyota" horn button and the mounting surface of the steering wheel.

Jason
Northern VA

 

[Cruiserhead05]

good rear bumperretes and step for tub bumper

I have a fairly nice confer tube rear bumper on my 40 right but am looking to get some nice gray bumperettes and a nice rear step to go in place of it. if anyone has these parts to sell or trade please tell me.

 

[dd113]

4" lift springs needed

I need a set of 40 series 4" lift springs. Any brand is fine. I just need to get through the spring then do the SOA over the summer.

 

[Cable Guy]

Need stock FZJ80 coils in Sacramento area

I have a friend with a 94 4Runner that is sagging in the rear. I have heard that 80 coils will give 3" of lift. Let me know what you have.
Jeff

 

[3_puppies]

good rear bumperretes and step for tub bumper

I've got one good bumperette and one not so good, I can dig them out. I don't have a step, but I think from another post the year is important. As it changed around 72-73-74 years not certain

 

[Cruiserhead05]

Re:good rear bumperretes and step for tub bumper

Well the it is an 82 for what it is worth. Also do you have any pics.?

 

[sdgraber]

Wanted-Fj40 Front Bib Assembly 79-up

I have a front apron from a 78 FJ40 with bottom bevel mount, red, some rust on bottom, no bib though (if the bib is the smaller long egg looking piece that attaches to the apron?)...and the lights have to stay in my ride so its really just the apron...give a holler if your interested, I can post a pic if you'd like? $40 would probably do it and I'm in Colorado for shipping.

Scott
78 FJ 40 "Rudy"

 

[3_puppies]

good rear bumperretes and step for tub bumper

I'll need your e-mail, as it's not on your profile. I cansend you pics tomorow

 

[Cruiserhead05]

Re:good rear bumperretes and step for tub bumper

My email is Cruisrhead05@yahoo.com

 

[Cruiserhead05]

Re:good rear bumperretes and step for tub bumper

scrap that.... Cruiserhead05@yahoo.com

 

[buckroseau]

looking for driver side seat rail assemblies

Wondering if anyone has a set of the sliding seat rails that go below the driver seat, there are 2 of them. That they want to get rid of? Or, where to get a set of reasonably priced used ones?

Please let me know at: roseauace@wiktel.com

Pics would be nice

Thanks, Matt

 

[3_puppies]

looking for driver side seat rail assemblies

I'll send you an e-mail

 

[bjowett]

Need stock FZJ80 coils in Sacramento area

The cruiser coils will work, however, there are quite a few different versions, and all cruiser use a left and right spring, one is taller. I have several sets kicking around, as I'm sure a few other folks around here do, too. Make an offer.

Lastly, run over to ebay - good deal.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=33582&item=2456173463

 

[lagwagon]

Need stock FZJ80 coils in Sacramento area

I have stock coils in Davis.
Jeff 530-753-5768

 

[dd113]

F engine crankcase endplate

Are you talking about the ft plate that the timing gear cover bolts to?

 

[godzilla]

Wanted-Fj40 Front Bib Assembly 79-up

Grabber, thanks for the offer, but I'm looking for the newer style bezel(the oval part), but the one I need is square on the ends. Thanks, Pete

 

[OlympiaFJ60]

3F-E air filter assembly `head'/`cap'

If you are still looking I have one.

Brandon

Olympia, WA

 

[Cable Guy]

Need stock FZJ80 coils in Sacramento area

I checked out the coils on ebay. They give 1 1/2" lift (back to level) and measure 15" tall. I suppose I would need to measure the 80 coils to see if I need 2 driver side or 2 pass. side coils. He just wants it to sit level or maybe a little high in the rear because he tows a quad with a trailer. Jeff, I will give you a call. Brian, are you local also?
Thanks,
Jeff