Do not Reply, See thread in Stickies - 2015 HAMOM Schedule (1 Viewer)

[dbenke]

OK, mine will (yes, I said WILL) be done before the next HAMOM, so think about who is next.
April 11.
We can wrench at my house if wanted on not, either is OK with me.

 

[southerncruiser62]

Sorry I didn't make it back by today. Had another project to complete and only a few weekends left. Shelleys been asking me to replace the stairs for a while and now it's done

David things look great. Would love to be involved in the bumper fab work. Perfect opportunity for plasma and MIG.

 

[greenseaman]

April 11 sounds good! Hopefully I can make the next one!!!

 

[dbenke]

I got some of the parts cleaned up today

 

[dbenke]

I just ordered the rest of the small parts for the axle.
Brake lines, p/s seal, trans mount, and tie rod ends.

Tim, the water leak is the radiator cap...strange it just started leaking while we were under it???

 

[Beau Diddly]

I just ordered the rest of the small parts for the axle.
Brake lines, p/s seal, trans mount, and tie rod ends.

Tim, the water leak is the radiator cap...strange it just started leaking while we were under it???

Maybe it was the altitude? If you need a hand, let someone know.

 

[CharlestonG8R]

Hey Tim, I assume you were able to replace your starter Just curious, how'd you gain access to that upper bolt? Did you go from the wheel well? Seemed like there was way too much "stuff" in the way to be able to go from the engine compartment...

 

[Beau Diddly]

Hey Tim, I assume you were able to replace your starter Just curious, how'd you gain access to that upper bolt? Did you go from the wheel well? Seemed like there was way too much "stuff" in the way to be able to go from the engine compartment...

By "stuff", you probably mean the heavy layer of mud that mysteriously appeared because my son said he didn't go muddin'. I was trying to get to it from wrong side of the bolt that went through it (obstructed and covered with mud, I H8 mud). David accessed the other end of the bolt and it came out without much problem, but still from underneath. You can see it from the top, but it's hard to access unless you have long skinny arms.

How's the back?

 

[BenMara]

Looks like Yall have been really busy

 

[mmacpherson]

I've got an OME suspension I need to put on my truck if everyone's up for helping next HAMOM. Also got a couple other things we can tend to - my tach and rear window aren't working. See y'all at David's on the 11th!

 

[CharlestonG8R]

I've got an OME suspension I need to put on my truck if everyone's up for helping next HAMOM. Also got a couple other things we can tend to - my tach and rear window aren't working. See y'all at David's on the 11th!

Did you get the caster correction bushings?

 

[dbenke]

He has an HJ61, leaf springs. plus, he is lowering it.

 

[CharlestonG8R]

OH, never mind then! Shouldn't take much time. David, didn't you and Greg remove your front axle in just over an hour?

 

[Beau Diddly]

If possible, my power steering pump is going out and I need to replace it. I'll be there 4/11 regardless.

 

[dbenke]

we can do that Tim. I heard it when you left Sunday.
we didn't have the springs off, Jeremy buy the axle was stripped

 

[Beau Diddly]

How not to have a HAMOM

 

[ErikinSC]

^^^ Doing it wrong!

 

[dbenke]

i hate when that happens

 

[dbenke]

OK, on the 11th, we have:

Swap springs on Mark's hj61
P / S pump on Tim's 80
Maybe finish a few small things on my 62
Anybody else???

 

[greenseaman]

Put me down for an oil and filter change on the Tacoma maybe, I need to figure out if it's due yet...