Broken AC line bracket on radiator

[mrbigboy]

Can anyone tell me the part number for this AC line bracket attached to the top of the radiator? Found mine busted the other day.

 

[RockyLC]

I have been looking for this part number as well. Any luck?

 

[guerasfj60]

88718-60880 Clamp, pipe

 

[abuck99]

You'll want to keep an eye on that radiator. The brown color tank= limited life remaining.

 

[RockyLC]

Agree with abuck99. Mine looked like that and generated a nice crack up top. Easy replacement and there are plenty of threads on here that show step by step.

 

[shtbrwn86]

I know this is an old thread, but based on another similar thread I purchased this. Haven't actually driven the LX yet, but this was a super simple install and they fit fine. They are about 3mm taller than the original isolator mounts that were in there but can't see that being a problem. Certainly didn't to spend $50+ when the rubber part was all that failed.
uxcell 25 x 20mm Rubber Mounts,Vibration Isolators,Shock Absorber with M6 x 18mm Studs 2pcs

 

[golfer2000]

I know this is an old thread, but based on another similar thread I purchased this. Haven't actually driven the LX yet, but this was a super simple install and they fit fine. They are about 3mm taller than the original isolator mounts that were in there but can't see that being a problem. Certainly didn't to spend $50+ when the rubber part was all that failed.
uxcell 25 x 20mm Rubber Mounts,Vibration Isolators,Shock Absorber with M6 x 18mm Studs 2pcs

On this, I found that there is actually a shorter one offered by Amazon that is awesome (20 x 15mm). I chopped the studs to make them shorter and it's as good as new. They come in a pack of 4 so I have extras. Not sure how much they are to ship but I can send one out if you need it. Just cover shipping.


Asin# B08CVGV48L

 

[Flipped Bezel]

I know this is an old thread, but based on another similar thread I purchased this. Haven't actually driven the LX yet, but this was a super simple install and they fit fine. They are about 3mm taller than the original isolator mounts that were in there but can't see that being a problem. Certainly didn't to spend $50+ when the rubber part was all that failed.
uxcell 25 x 20mm Rubber Mounts,Vibration Isolators,Shock Absorber with M6 x 18mm Studs 2pcs

@shtbrwn86 Do you recall which thread it was that had the discussion about these aftermarket bracket insulators? I am needing to get mine replaced and a search did not show up any results. Thanks!

Edit: I think I found the old thread. under hood checking and..

 

[golfer2000]

You need the bracket or just the rubbers?

@shtbrwn86 Do you recall which thread it was that had the discussion about these aftermarket bracket insulators? I am needing to get mine replaced and a search did not show up any results. Thanks!

 

[Flipped Bezel]

Just the rubber cushions

 

[golfer2000]

I sent you a message.

Just the rubber cushions

 

[Flipped Bezel]

I got the Amazon isolators that @shtbrwn86 linked above installed on my LX today. They are a little taller than the OEM rubbers and I stacked a couple of fender washers that I had to give me a little more clearance for my HID wiring harness that runs through the bracket.

The threaded end sticks up a little higher than the originals but no issues and plenty of clearance beneath and above without touching anything.

 

[shtbrwn86]

I got the Amazon isolators that @shtbrwn86 linked above installed on my LX today. They are a little taller than the OEM rubbers and I stacked a couple of fender washers that I had to give me a little more clearance for my HID wiring harness that runs through the bracket.

The threaded end sticks up a little higher than the originals but no issues and plenty of clearance beneath and above witohut touching anything.

View attachment 2491947

Nice! I don't think the few mm of extra height matters one bit.