80 series with Roof Nest Falcon XL roof top tent (1 Viewer)
- Thread starter L450X
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Eyeing this exact setup with the nice discount they're running on the XL.
I think I could handle a bit of stickout for some extra room at night. I'm 6' 3" and the wife is 6".
A bit of room is nice, especially during summer months. The near-instant deploy is certainly appealing as well.
I think I could handle a bit of stickout for some extra room at night. I'm 6' 3" and the wife is 6".
A bit of room is nice, especially during summer months. The near-instant deploy is certainly appealing as well.
- Thread starter
- #3
Yeah that
I was impressed when it showed up, would have liked to pay less but was not under impressed after unboxing.
Working on it currently and something to note is with the bowfin rack, it does rattle against the cross bars that aren’t clamped to it.
I’m currently adding the ones from the ARB kit to mitigate.
ARB 815118 Rooftop Tent Mounting Fit Kit Rooftop Ten... Amazon product ASIN B07MHFWMWH
Also, the bowfin awning brackets do fit under the tent fine but at least with the XL don’t stick out far enough to have the tent sit with even overhang. There’s obviously awning brackets for these tents do not a big deal there.
6’2” here and I feel comfortable in it (feet do touch end of you have them straight up. But pretty comfy all things considered.
I liked that the tent came with the hardware pre threaded and lock tight…ed ready to slide in. It also came with a good bit of extras like a sand mat and pop up shower room
$600 off is hard to argue with.
I was impressed when it showed up, would have liked to pay less but was not under impressed after unboxing.
Working on it currently and something to note is with the bowfin rack, it does rattle against the cross bars that aren’t clamped to it.
I’m currently adding the ones from the ARB kit to mitigate.
ARB 815118 Rooftop Tent Mounting Fit Kit Rooftop Ten... Amazon product ASIN B07MHFWMWH
Also, the bowfin awning brackets do fit under the tent fine but at least with the XL don’t stick out far enough to have the tent sit with even overhang. There’s obviously awning brackets for these tents do not a big deal there.
6’2” here and I feel comfortable in it (feet do touch end of you have them straight up. But pretty comfy all things considered.
I liked that the tent came with the hardware pre threaded and lock tight…ed ready to slide in. It also came with a good bit of extras like a sand mat and pop up shower room
- Thread starter
- #4
Dilspec
SILVER Star
Here’s a Bowfin with CVT Mt. Hood. Similar setup as yours.
- Thread starter
- #6
Nice looking rig too.
Dilspec
SILVER Star
Thanks, that was in Moab, UT.
TurboDennis
SILVER Star
I have the "regular" version that i made custom direct mounts for, for a much lower profile than mounting on a roof rack. Made from 316 stainless steel.
I will probably upgrade to the XL version, as the regular is too small for 2 adults and 1 child. XL should be much more comfortable.
I will probably upgrade to the XL version, as the regular is too small for 2 adults and 1 child. XL should be much more comfortable.
- Thread starter
- #9
Those look good. I bet that’s a lot more low profile and clean looking. You fixin to do the same style brackets for the XL or you think it’ll be too wide?
TurboDennis
SILVER Star
Yes, i will do the same style mounts for the XL as well. Will need to adjust the design slightly, but It's doable. The advantages of ultra low profile brackets like these are just too big to pass up.
Last edited:
REKCUT
SILVER Star
Looks very nice but in my part of the country the bowfin rack with just an awing gets beat up from the trees. I don't think i could squeeze that XL down the trails around here.
Still very nice looking
Still very nice looking
