3D Printing and GX 460 parts (1 Viewer)

[r2m]

Here's the user's site with all the resins and settings for Anycubic Photon Mono X.
Anycubic has really developed a following and has some really good products.

Anyways, we would probably get back to the regularly scheduled thread...
Thanks to everyone else letting us rabbit trail a wee bit.

 

[TheNomad]

I need to get back to spending more time on some projects, and to get better at modeling. I'm stuck at beginner mode since I teach HS freshmen intro classes. I'm bogged down in just management. Here are some grab handle covers I made so I could mount paracord grab handles. Then of course the obligatory cup holder that still needs finishing.

 

[r2m]

I need to get back to spending more time on some projects, and to get better at modeling. I'm stuck at beginner mode since I teach HS freshmen intro classes. I'm bogged down in just management. Here are some grab handle covers I made so I could mount paracord grab handles. Then of course the obligatory cup holder that still needs finishing.
View attachment 3249762View attachment 3249764View attachment 3249765

Did you print the handles in nylon or carbon fiber? Anything else will probably shear at a layer or break.
Love the idea, but have you tested the strength of those grab handles? You may want to try hanging some weights (maybe yourself or someone else who's heavy?) to test unless you have at least a 1000 N load cell (and that would probably be on the light side).
Just saying that I'd hate to have one of those handles break on me when I'm holding on for dear life!

 

[TheNomad]

The plates are nylon and I need to print them again as the setting wasn't on full solid print. But the handles themselves are on a steel motorcycle tie down ring bolted through the printed plate into the chassis. These are just cosmetic to cover the odd holes in the factory location.

 

[r2m]

The plates are nylon and I need to print them again as the setting wasn't on full solid print. But the handles themselves are on a steel motorcycle tie down ring bolted through the printed plate into the chassis. These are just cosmetic to cover the odd holes in the factory location.

Ahhhh, Bravo!! I was hoping you'd designed it to not just yank on the 3D printed parts.

 

[Acrad]

Lexus GX460 Cup Holder - TEQ by Lunar_Prado

GX460 Cup Holder - TEQ logo design. Note: Corrected Logo orientation

www.thingiverse.com

Awning brackets for Lexus GX460 stock roof rails

Awning brackets for Lexus GX460 stock roof rails by 1974Boler

I wanted to mount a roof awning on my Lexus GX 460 using the stock aero type cross bars. Using these brackets along with aluminum T-slot channel results in an adjustable clamp. The T-channel needs the holes counter sunk to accept a 1/4"x20 - 1.5" long flat head bolt, the bolt heads should sit...

www.thingiverse.com

RAM Phone Mount Base

Lexus GX460 RAM Phone Mount Base by 1974Boler

I wanted a way to mount my cell phone that allows quick removal of the phone & brackets and keeps the holder base concealed in the front console tray still allowing the lid to close. Using the RAM arm and phone mount, the 3D printed base is attached inside the console tray with 2 sided tape. I...

www.thingiverse.com

Aside from saying LX 570 this should work with GX 460 card key as well

LX 570 Wallet card key sleeve by SergeyF

This is sleeve for Wallet card key for Lexus LX570

www.thingiverse.com

3D Printing and GX 460 parts - ClubLexus - Lexus Forum Discussion

GX - 2nd Gen (2010-2023) - 3D Printing and GX 460 parts - Surely many in this group have 3D printers... I finally decided to dive into one. I've been playing around with a new Prusa Mini (https://www.prusa3d.com/category/original-prusa-mini/)+ manufactured in the Czech Republic. I hadn't heard...

www.clublexus.com

Parking Sensor Sount for Steel Bumper by maingear81

I needed to install the factory GX460 front parking sensors 89341-48010 on an aftermarket steel bumper (Ironman 4x4 Classic). I drilled 3/4" (18mm) holes, then used 3m outdoor mounting tape to secure the adapters to the inside of the bumper. Light sanding was required inside the keyed hole to...

www.thingiverse.com

 

[r2m]

Lexus GX460 Cup Holder - TEQ by Lunar_Prado

GX460 Cup Holder - TEQ logo design. Note: Corrected Logo orientation

www.thingiverse.com

Awning brackets for Lexus GX460 stock roof rails

Awning brackets for Lexus GX460 stock roof rails by 1974Boler

I wanted to mount a roof awning on my Lexus GX 460 using the stock aero type cross bars. Using these brackets along with aluminum T-slot channel results in an adjustable clamp. The T-channel needs the holes counter sunk to accept a 1/4"x20 - 1.5" long flat head bolt, the bolt heads should sit...

www.thingiverse.com

RAM Phone Mount Base

Lexus GX460 RAM Phone Mount Base by 1974Boler

I wanted a way to mount my cell phone that allows quick removal of the phone & brackets and keeps the holder base concealed in the front console tray still allowing the lid to close. Using the RAM arm and phone mount, the 3D printed base is attached inside the console tray with 2 sided tape. I...

www.thingiverse.com

Aside from saying LX 570 this should work with GX 460 card key as well

LX 570 Wallet card key sleeve by SergeyF

This is sleeve for Wallet card key for Lexus LX570

www.thingiverse.com

3D Printing and GX 460 parts - ClubLexus - Lexus Forum Discussion

GX - 2nd Gen (2010-2023) - 3D Printing and GX 460 parts - Surely many in this group have 3D printers... I finally decided to dive into one. I've been playing around with a new Prusa Mini (https://www.prusa3d.com/category/original-prusa-mini/)+ manufactured in the Czech Republic. I hadn't heard...

www.clublexus.com

Parking Sensor Sount for Steel Bumper by maingear81

I needed to install the factory GX460 front parking sensors 89341-48010 on an aftermarket steel bumper (Ironman 4x4 Classic). I drilled 3/4" (18mm) holes, then used 3m outdoor mounting tape to secure the adapters to the inside of the bumper. Light sanding was required inside the keyed hole to...

www.thingiverse.com

Boy! you're going to town with your printer! Great work!!

 

[tech703]

Would anyone be willing to try printing something for me, I can paypal for the materials and shipping. I have this file for a bracket to add some lights to a roof rack

Rock Light Mount Victory Roof Rack by techh703 - https://www.thingiverse.com/thing:5964660

 

[r2m]

Would anyone be willing to try printing something for me, I can paypal for the materials and shipping. I have this file for a bracket to add some lights to a roof rack

Rock Light Mount Victory Roof Rack by techh703 - https://www.thingiverse.com/thing:5964660

Note if you get someone to print your brackets, make sure they use the right material. Don't have it print in PLA, but prefer Nylon, ABS or some other UV, chemical and weather resistant material.

 

[r2m]

Lexus GX460 Cup Holder - TEQ by Lunar_Prado

GX460 Cup Holder - TEQ logo design. Note: Corrected Logo orientation

www.thingiverse.com

Awning brackets for Lexus GX460 stock roof rails

Awning brackets for Lexus GX460 stock roof rails by 1974Boler

I wanted to mount a roof awning on my Lexus GX 460 using the stock aero type cross bars. Using these brackets along with aluminum T-slot channel results in an adjustable clamp. The T-channel needs the holes counter sunk to accept a 1/4"x20 - 1.5" long flat head bolt, the bolt heads should sit...

www.thingiverse.com

RAM Phone Mount Base

Lexus GX460 RAM Phone Mount Base by 1974Boler

I wanted a way to mount my cell phone that allows quick removal of the phone & brackets and keeps the holder base concealed in the front console tray still allowing the lid to close. Using the RAM arm and phone mount, the 3D printed base is attached inside the console tray with 2 sided tape. I...

www.thingiverse.com

Aside from saying LX 570 this should work with GX 460 card key as well

LX 570 Wallet card key sleeve by SergeyF

This is sleeve for Wallet card key for Lexus LX570

www.thingiverse.com

3D Printing and GX 460 parts - ClubLexus - Lexus Forum Discussion

GX - 2nd Gen (2010-2023) - 3D Printing and GX 460 parts - Surely many in this group have 3D printers... I finally decided to dive into one. I've been playing around with a new Prusa Mini (https://www.prusa3d.com/category/original-prusa-mini/)+ manufactured in the Czech Republic. I hadn't heard...

www.clublexus.com

Parking Sensor Sount for Steel Bumper by maingear81

I needed to install the factory GX460 front parking sensors 89341-48010 on an aftermarket steel bumper (Ironman 4x4 Classic). I drilled 3/4" (18mm) holes, then used 3m outdoor mounting tape to secure the adapters to the inside of the bumper. Light sanding was required inside the keyed hole to...

www.thingiverse.com

BTY, have you had a chance to try the under seat vent?
I was checking out something (unrelated) under the drivers seat and had to slide it full forward. I forgot that there are those vents under there.
So that's where the printed parts connects to! Does it fit well? I can now see how that could provide a lot more cooling. Not necessarily more CFM, but much cooler air, which in itself would be very beneficial.

 

[Acrad]

Unfortunately I haven't tested yet.. it's been a cold spring with rain, sleet and hail.

I did have to make the print 40% wider and then just slides right on. I think the one I was originally printing was for a '14+ Lexus IS

 

[TheNomad]

I'm going to bend up a plastic sheet and slide it under to test it. Should direct the flow as well for a test.