I am selling my FJ-60. I built this cruiser with the plan to make it a trail vehicle. After putting all the time and effort into building this rig, I just can't bring myself to tear it up by bashing it into trees and rocks. I purchased this cruiser a while back almost stock aside from the engine conversion. Everything works except the A/C (see below) I will try to get the hoses made over the next few weeks and get it going (unless it sells before then) I am asking $8,500 for the cruiser. It is located in Longview, TX. If my mud box fills up, please feel free to email me at kelsey.koon@gmail.com
Will post more pics as soon as possible.
1987 FJ-60
133,452 Miles
Fresh Paint (last year)
Chevy 350 w/ Holley truck avenger carb (670 cfm) (unknown miles on conversion)
Corvette ram horn headers
New Exhaust w/ 2.5” free flow cat and muffler w/ cut out
Factory 4 speed transmission/t-case (Advanced Adapters Kit to mate up to 350)
2-1/2” – heavy lift springs
HD greasable shackle kit
Pro Comp Shocks
SOA Conversion w/ front knuckles turned to correct pinion angle (Ruff Stuff Specialties kit )
HD Crossover steering setup w/ FJ80 rod ends & hydraulic assist (1.5” x 6” ram)
Drilled and tapped existing Toyota box rebuilt w/ new seals.
Saginaw Power steering pump mod w/ fluid cooler
4.56:1 gears F/R w/ Aussie lockers F/R
Rebuild axles w/ new bearings/seals when gears were installed
Custom Dual Cardin drive shafts F/R (Tom Woods Rear)
Extended front sway bar
Extended stainless steel braided brake lines front and rear
Extended axle vent tubes
New rear brake shoes
1.5” wheel Spacers from spidertrax
15x10 street lock wheels
36x13.5x15 Super Swamper Irok Radials
Custom Front bumper with shackles and Warn 8274 8000lb. winch (new motor & remote)
Custom Rear bumper with swing out tire carrier and CB mount and shackles
Yakima Roof Rack
New hood mod w/ hydraulic lift arms (replaced old spring lift mechanism)
Molded dash overlay installed
CD Player w/ new speakers & aux input for ipod
Have all the parts for the A/C (new compressor as well) just need the custom hoses made
New Centerforce clutch w/ pressure plate in box (current clutch is good)
All gauges work w/ mechanical temperature gauge as well
Replaced Oil pan gasket, rear main seal, and valve cover seals (all Fel-Pro gaskets)
Minimal rust on body and frame (see photos)
Bad:
Typical tear in drivers seat
Missing bottom chrome trim piece on drivers side
Rear tailgate carpet needs attention
Transfer case leaks gear oil (I have changed the front and rear output seals which slowed it down, but did not stop it)
A small oil leak on the engine, think it is the timing cover gasket (one of the few I have not changed)
Will post more pics as soon as possible.
1987 FJ-60
133,452 Miles
Fresh Paint (last year)
Chevy 350 w/ Holley truck avenger carb (670 cfm) (unknown miles on conversion)
Corvette ram horn headers
New Exhaust w/ 2.5” free flow cat and muffler w/ cut out
Factory 4 speed transmission/t-case (Advanced Adapters Kit to mate up to 350)
2-1/2” – heavy lift springs
HD greasable shackle kit
Pro Comp Shocks
SOA Conversion w/ front knuckles turned to correct pinion angle (Ruff Stuff Specialties kit )
HD Crossover steering setup w/ FJ80 rod ends & hydraulic assist (1.5” x 6” ram)
Drilled and tapped existing Toyota box rebuilt w/ new seals.
Saginaw Power steering pump mod w/ fluid cooler
4.56:1 gears F/R w/ Aussie lockers F/R
Rebuild axles w/ new bearings/seals when gears were installed
Custom Dual Cardin drive shafts F/R (Tom Woods Rear)
Extended front sway bar
Extended stainless steel braided brake lines front and rear
Extended axle vent tubes
New rear brake shoes
1.5” wheel Spacers from spidertrax
15x10 street lock wheels
36x13.5x15 Super Swamper Irok Radials
Custom Front bumper with shackles and Warn 8274 8000lb. winch (new motor & remote)
Custom Rear bumper with swing out tire carrier and CB mount and shackles
Yakima Roof Rack
New hood mod w/ hydraulic lift arms (replaced old spring lift mechanism)
Molded dash overlay installed
CD Player w/ new speakers & aux input for ipod
Have all the parts for the A/C (new compressor as well) just need the custom hoses made
New Centerforce clutch w/ pressure plate in box (current clutch is good)
All gauges work w/ mechanical temperature gauge as well
Replaced Oil pan gasket, rear main seal, and valve cover seals (all Fel-Pro gaskets)
Minimal rust on body and frame (see photos)
Bad:
Typical tear in drivers seat
Missing bottom chrome trim piece on drivers side
Rear tailgate carpet needs attention
Transfer case leaks gear oil (I have changed the front and rear output seals which slowed it down, but did not stop it)
A small oil leak on the engine, think it is the timing cover gasket (one of the few I have not changed)
